Siemens DF8000 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 46

Siemens DF8000 Скачать руководство пользователя страница 21

17

Building Technologies

048_DMS_DF8000_ICC_MP4.15_A6V10081388_c_en.doc

Fire Safety & Security Products

06.2008

4.3

Power supply

A local DC power supply (11... 33 VDC) is required for each unit.

Internal and the external circuits should receive separate input voltages and the
CPU module has two separate power supply inputs, as illustrated in Fig. 9. The
first supplies the CPU and the internal I/O circuits (terminals 2-3), whereas the
second one is used to supply the external I/O circuits (terminals 4-5).

Power supply can range from 11 to 33 VDC, stabilised (see Tab.8).

Internal circuits

11… 33 VDC

External circuits

11… 33 VDC

Max. current absorption for 6 mod. (int. @ 13,8V) 220 mA (all I/O active); 75 mA (no I/O active)
Max. current absorption for 6 mod. (int. @ 27V)

140 mA (all I/O active); 60 mA (no I/O active)

Max. current absorption for 6 mod. (ext. @ 13,8V) 400 mA (all I/O active); 25 mA (no I/O active)
Max. current absorption for 6 mod. (ext. @ 27V)

450 mA (all I/O active); 30 mA (no I/O active)

Tab.8.

DF8003 power supply

The CPU modules are equipped with two lines of 9 terminals:
the bottom line is numbered from 1 (left) to 9 (right) whereas the top one is num-
bered, in the opposite direction, from 10 (right) to 18 (left), refer to Fig. 9.

Fig. 9

Power supply

EMI filters on the DF8003 are dimensioned for the documented power supply rat-
ings.

Important: DIN rail must have a good earth connection to ensure proper operation
of EMI filters

10

11

12

13

14

15

16

17

18

9

8

7

6

5

4

3

2

1

1

DF8003
CPU

1

8

FLT

TX

RX

PWR

RST

External circuits (4-5)

Internal circuits (2-3)

«
...
19
20
21
22
23
...
»

Содержание DF8000















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды