background image

4/11 

Siemens Building Technologies 

RXZ90.1 – Receiver with PPS2 interface 

CA2N1644en 

Building Automation 

 

07.2001 

Commissioning and establishing communication

 

Please do not make any adjustments without a careful reading of the following 
commissioning notes. 
 

• 

The unit(s) must be mounted at least 1 metre from the receiver 

• 

Where there is more than one receiver in the same building, communication must 
be established with each receiver separately, after a time delay. This is because 
commissioning signals can be received from adjacent rooms, or even from 
neighbouring buildings during the commissioning process.  

 

Communication between the wireless room unit and the receiver can be 

established

 

either before or after installation. 

Checking

 the wireless communication (see below) 

only makes sense when all the devices are mounted. 
 

PLEASE FOLLOW THE INSTRUCTIONS EXACTLY IN THE SEQUENCE SHOWN: 

1.  Snap-mount the RXZ90.1 receiver on the mounting plate (power ON: the receiver 

goes into "Installation" mode). 

2.  Insert batteries in all the allocated wireless room units (max. 5) or remove the 

isolating strip from the batteries already inserted. (power ON: the room unit 
transmits its unique ID to the receiver). 

3.  You can establish communication with the next receiver as soon as the 4-minute 

"Installation mode" has expired in all the room units. 

 
Brief pressure (<1 s) on the button adjacent to the battery holder of the room unit 
allows you to check the wireless link with the room controller. After receiving this 
signal, the receiver will close the PPS2 interface for 1.5 s. This briefly extinguishes 
the display on the connected RXT20.1 service terminal (or the green LED on the 
diagnostic plug, see 

Diagnostics,

 below). If there is no wireless link with the receiver, 

the display on the service terminal (or the green LED) will not be extinguished. 

Pressing the button on the room unit causes the controller to send its Neuron ID in 
the same way as for registration on the LON bus. However, when checking the 
wireless communication, we are not interested in the Neuron ID, but in observing 
whether the controller reacts to the wireless signal. 

 

Additional functions for establishing communication

 

Sustained pressure (>5s) on the button of the room unit to be removed.  
The receiver will delete only this room unit from its device list.  

Caution: Wait 4 minutes before changing any further links. 
 
Sustained pressure (>5s) on the button of the room unit to be replaced.  
The receiver will delete this room unit from its device list and then switch to 
installation mode. 

Insert batteries in the replacement unit(s); these will switch to installation mode.  

The receiver recognises all newly connected room units and adds these to its device 
list. 

Caution: Wait 4 minutes before changing any further links. 

 

STOP

 

Caution! 

Establishing 
communication  
for the first time 

Checking the 
wireless 
communication 

Remark 

Cancelling the link with 
a room unit 

Replacing room units 
(replacement units) 

Содержание DESIGO RX Series












Отзывы: