Before using for the first time
en
15
K
Before using for the first
time
Before using for the first time
Before you can use your new appliance, you must
make some settings. You must also clean the cooking
compartment and accessories.
Before using for the first time
Before using the appliance for the first time, ask your
water supplier about the hardness of your tap water.
To ensure that the appliance can reliably remind you to
descale it when required, you must set your water
hardness range correctly.
Caution!
■
The appliance may become damaged due to the
use of unsuitable liquids.
Do not use distilled water, highly chlorinated tap
water (>40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
■
Malfunctions may occur when using filtered or
demineralised water.
The appliance may request that you top up the water
tank even though it may be full, or operation with
steam is cancelled after approx. two minutes.
If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ratio
of one to one.
Notes
■
If your water is very hard, we recommend that you
use softened water.
■
If you only use softened water, you can set the water
hardness range to "softened".
■
If you use mineral water, set the water hardness
range to "4 very hard".
■
If you use mineral water, you must only use non-
carbonated mineral water.
Initial use
After connecting the appliance to the power or following
a power cut, the settings for initial use are shown in the
display.
Note:
You can change these settings at any time in the
basic settings.
Setting the language
German is the preset language.
1.
Use the rotary selector to select the required
language.
2.
Touch the
Æ
arrow.
The next setting appears.
Setting the clock
The time starts at 12:00.
1.
Use the rotary selector to set the current time.
2.
Touch the
Æ
arrow
Setting the date
The default date is 1.1.2014.
1.
Always touch the
Æ
arrow to move to the next
setting.
2.
Use the rotary selector to set the current day, month
and year.
Setting the water hardness
The default water hardness setting is "very hard".
Change this setting if your water is softer. You can ask
your water supplier about the water hardness level.
1.
Set the hardness using the rotary selector.
2.
Touch the
Æ
arrow.
A message appears on the display confirming that
the initial use has been completed.
With HomeConnect
1.
Touch "Set using the assistant".
2.
Further instructions can be found in section
Calibrating the appliance and cleaning the
cooking compartment
The boiling point of water depends on the air pressure.
During calibration, the appliance self-adjusts to the
pressure ratio at the installation location. This will
happen automatically the first time steam-assisted
cooking is used. This produces a lot of steam.
Preparing the appliance for calibration
1.
Remove the accessories from the cooking
compartment.
2.
Remove any leftover packaging, such as polystyrene
pellets, from the cooking compartment.
3.
Before calibrating the appliance, wipe the smooth
surfaces in the cooking compartment with a soft,
damp cloth.
Calibrating the appliance and cleaning the cooking
compartment
Notes
■
Calibration cannot be started until the cooking
compartment is cold (room temperature).
■
Do not open the appliance door while calibration is
in progress, as this will abort the calibration process.
Water hardness range
Setting
0
0 softened
1 (up to 1.3 mmol/l)
1 soft
2 (1.3 - 2.5 mmol/l)
2 medium
3 (2.5 - 3.8 mmol/l)
3 hard
4 (above 3.8 mmol/l)
4 very hard
Содержание CS858GR.6B
Страница 2: ......
