Siemens CPU 1518HF-4 PN Скачать руководство пользователя страница 33

Страница: 33 / 44

Alarm, error and system messages

4.1 Status and error display of the CPU

CPU 1518HF-4 PN (6ES7518-4JP00-0AB0)

Equipment Manual, 05/2021, A5E49868646-AA

Note
MAINT LED of the two CPUs

The MAINT LEDs of both CPUs only go out when the following conditions are fulfilled:
•

The CPUs are in the RUN-Redundant system state.

•

No maintenance is demanded.

Note
LED displays in redundant operating state

In the RUN-Redundant system state, the LED displays on both CPUs are identical (exception:

you are performing an LED flash test on one CPU).

Meaning of LINK RX/TX LED

Each port of the X1, X2, X3, X4 and X5 interfaces has a LINK RX/TX LED. The table below

shows the various LED patterns of the CPU 1518HF-4 PN ports.

Table 4- 2

Meaning of LINK RX/TX LED

LINK TX/RX LED

Meaning

Off

There is no connection between the interface of the device and a communication partner.

No data is currently being sent/received via the interface.

There is no LINK connection.

The redundancy connections were interrupted.

Flashes green

The CPU performs an LED flash test.

Illuminated green

There is a connection between the interface of the device and a communication partner.

The redundancy connections are OK.

LED flashes

yellow/green

Data is currently being received or sent by a communication partner via the interface of the

device.

Note
"LED" instruction

You can read the status (e.g. "On" or "Off") of LEDs of a CPU or a module using the "LED"

instruction. Note, however, that it is not possible to read the LED status of the LINK RX/TX

LEDs on all S7-1500 R/H CPUs.
You can find additional information on the "LED" instruction in the STEP 7 online help.

Содержание CPU 1518HF-4 PN













































Результаты поиска

Содержание CPU 1518HF-4 PN

Отзывы:

Похожие инструкции для CPU 1518HF-4 PN

Бренды по названию

Популярные бренды

Siemens CPU 1518HF-4 PN, Руководство по эксплуатации оборудования

Результаты поиска

Содержание CPU 1518HF-4 PN

Отзывы:

Похожие инструкции для CPU 1518HF-4 PN

Бренды по названию

Популярные бренды