Siemens CF62 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 42

background image

SIEMENS

CF62 Level 2 Service Manual

Copyright © Siemens Mobile

SSMC MD CCQ

All rights reserved

34 of 42

Internal Service Use Only

Siemenes Shanghai Technical Support Center

Master phone codes

The

Master Phonecode

is used to unlock blocked mobiles.

Master Phonecodes

can only be supplied for mobiles which have been delivered in a

regular manner.

Figure 3. Master phone code page

Simlock Unlock - Code

The

Simlock-Unlock-Codes

can only be generated if the following conditions are given:

•

Mobile must have an active

Simlock

inside.

•

The user must be given the authorization to obtain

Simlock Unlock- Codes

for the

variant of the operator to which the mobile was delivered last time.

«
...
32
33
34
35
36
...
»

Содержание CF62











































Отзывы:

Нет отзывов

Похожие инструкции для CF62

Бренд: Nec Casio Страницы: 390

Бренд: Unify Страницы: 2

Бренд: Hanlong Страницы: 68

STORM 9500 - STORM 9530 SMARTPHONE

Бренд: Blackberry Страницы: 36

Бренд: FAMOCO Страницы: 19

Бренд: WayteQ Страницы: 24

Бренд: VERTIS Страницы: 23

Бренд: iBall Страницы: 150

Бренд: GAI-Tronics Страницы: 92

Moment SPH-M900

Бренд: Samsung Страницы: 122

My Shot SCH-r430 series

Бренд: Samsung Страницы: 142

Mesmerize SCH-I500

Бренд: Samsung Страницы: 170

Messager SCH-r450 Series

Бренд: Samsung Страницы: 150

MYTHIC SGH-A897 Series

Бренд: Samsung Страницы: 202

Messager Touch SCH-R631

Бренд: Samsung Страницы: 165

MYTHIC SGH-A897 Series

Бренд: Samsung Страницы: 202

M620 - SPH UpStage Cell Phone

Бренд: Samsung Страницы: 340

Moment SPH-M900

Бренд: Samsung Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды