Siemens CERBERUS PYROTRONICS PXL Скачать руководство пользователя страница 45

Страница: 45 / 83

Programming

PXL Conventional Fire Alarm Control Panel

4 Programming the PXL Control Panel

INTRODUCTION

The following instructions will assist the user in programming the

PXL System. In addition to the instructions, definitions of many of the

PXL's features are also included for general information. Please note

that the system is designed to guide the user through the program-

ming functions without the need of the manual. Soon after you begin

to program the PXL you will find that you use this manual for refer-

ence purposes only.
The PXL software provides direction for all functions. Press the blue

Help (?) button on the user interface at any point in the program to

access the Help screens. These screens give a more detailed expla-

nation of the function to be performed.

The arrows (< , >) on the screen indicate the button to press to select

a particular item.

Firmware Revisions

This manual references PXL firmware Revision 4.0. Make note of the

following information for proper system operation:

PXL systems containing two PPS-10M power supply modules

must use PXL firmware Revision 3.0 or higher and PPS-10M

firmware Revision 2.0 or higher.

PXL systems using the CANADA country code selections de-

scribed below must use PCM-1 and PZE-4B firmware Revision

3.0 or higher.

PXL systems used as Remote Supervising Station Fire Alarm

systems must use PXL firmware Revision 4.0 or higher.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание CERBERUS PYROTRONICS PXL




















































































Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды

Siemens CERBERUS PYROTRONICS PXL, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды