Siemens CCWC1345-LX Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 34

Siemens CCWC1345-LX Скачать руководство пользователя страница 18

Install the camera

18

Siemens Building Technologies

Fire Safety & Security Products

08.2006

6 Install

the

camera

6.1 Installation

1.

Connect BNC cable to video output, please refer to chapter 5.1 Camera part
definition.

2.

Connect power source to power terminal.

3.

To reduce radiation sufficiently, please wind one turn around the core, see
figure below.

Location

Core illustration

Camera type

Power cable

LX

Power cable

MX

Y/C cable

LX / MX

CAUTION

If using a DC supply, make sure the polarity is correct. Incorrect connection may
cause malfunction and / or damage to the camera.

4.

Adjust backfocus: The backfocus is adjusted in the factory for a CS mount
lens as shipped, if re-adjust is necessary, please unlock screw. Enter

Back

Focus Format

in OSD (please refer to chapter 6.2.4.8), then rotate backfocus

wheel till a sharp image appears. Lock the screw tightly.

6.1.1

Using BNC composite video output

1.

Connect BNC cable to video output, please refer to chapter 5.1 Camera part
definition.

2.

Make sure that a proper BNC 75 Ohm cable is used.

3.

Switch on 75 Ohm termination in video receive equipment such as Monitor,
matrix or equivalent

6.1.2

Using twisted pair video output

1.

Connect twisted pair cable to TP-Output of camera, please refer to chapter
5.1 Camera part definition

2.

Connect suitable twisted pair receiver device (i.e. TP-RXMOD2)

3.

Setup TP transmitter using DIP-switches, please refer to chapter 5.2.1.

4.

Adjust twisted pair receiver to get best quality video-output, please refer to the
instruction manual of used twisted pair receiver

«
...
16
17
18
19
20
...
»

Содержание CCWC1345-LX



































Отзывы:

Нет отзывов