Siemens AQS2700 Скачать руководство пользователя страница 18

Страница: 18 / 40

Configurations
Push button configuration (QSA2700)

18 | 40

A6V11160936_en--_c

4.4 Push button configuration (QSA2700)

4.4.1 On-event addressing (Climatix

controllers configuration)

On-event addressing is a rapid configuration approach working together with

Siemens Climatix

controllers.

The sensor is wired and connected to the Climatix

controller via Modbus.

Press the
button for

LED

Action

More details

1…5 s

Constant red Press and hold the button

5…10 s

LED off

Release the button

Entering the addressing mode, LED

flashes yellow for 30 s.

●

Address is set to 246

temporarily.

Communication is established

automatically when:

●

Baud rate is 19200 (default).

●

Format is 1-8-E-1 (default).

●

Address is 246.

Then:

●

Master writes the Modbus

parameters.

●

Master writes “1” into register

4x0768 ("Bus configuration

command”) to activate the

change.

After a successful pairing, the LED

flashes green for 60 s, then turns to

permanent green.
Otherwise, the LED turns back to its

original state.

LED flashes

yellow for

0…30 s

Short press the button to fix

the address to 246.

If the LED is flashing, a short press of

the push button fixes the address to

246.
The LED is off for 2 s, then turns

yellow for 2 s and then turns to

permanent green.
The address is 246.
Further configuration should be

carried out from controller side.

Enter addressing mode and

configuration workflow via

push button

Содержание AQS2700









































Результаты поиска

Содержание AQS2700

Отзывы:

Бренды по названию

Популярные бренды

Siemens AQS2700, Основная документация

Результаты поиска

Содержание AQS2700

Отзывы:

Бренды по названию

Популярные бренды