manualshive.com logo in svg

Siemens A53689, Руководство по установке и эксплуатации

Поделиться
Скачать
Siemens A53689 Скачать руководство пользователя страница 43

TROUBLESHOOTING 

_________________________________________________________________________________________________________ 

4-1 

COM-00-21-04                                                                                                                                                          OCTOBER 2021 
Version No.: A.1 

SECTION 4 

TROUBLESHOOTING 

 

4 

TROUBLESHOOTING 

 
If properly configured, the Remote Station (RS) and the Base Station (BS) should connect within 
one minute after being turned on. If the connection is not established, then the following needs 
to be investigated. 
 

Table 4-1   Troubleshooting Matrix 

 

PROBLEM 

TROUBLESHOOTING PROCEDURE 

 
 
 

 

Configuration Mismatch 

Verify that both the BS and the RS are configured for the same 
configuration.  (Note that if the configuration is to be changed over the 
radio link, then it is essential to configure all RS units before configuring 
the BS unit as connectivity to the RS unit will be lost after the new 
configuration is implemented.) 
Symbolic Link: It is important to note that the system relies on symbolic 
links to the desired configuration file. Multiple configurations can be stored 
on each radio, but only the one linked is active. If the symbolic link is to the 
wrong configuration file, then the unit will not connect. 

 
 

 

Excessive Pathloss 

In a lab setup, verify that the attenuation between the BS and the RS is 
set properly and does not exceed 90 dB. (Do not power on the radios 
without the proper attenuation between the units). 

 

In an operational environment

, verify that the path loss is acceptable and 

that the connections to the antennas are secure and proper. Verify that the 
antennas are correctly installed per the RF plan. 

 

Cabling & Antennas 

Verify that both the BS and RS along with their associated RF cabling and 
antennas are properly grounded. 

 

 

Interference 

Perform an RF scan using Apollo to verify that the channel is clear of RF 
interference. Note that the radio has a very large RF range and as such, 
out of TX/RX band RF energy can affect the radio’s sensitivity. Proper 
use of external filters can reduce this interference. 

Содержание A53689







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды