Siemens 6GK1411-1AC00 Скачать руководство пользователя страница 34

Страница: 34 / 150

Installation, wiring, commissioning

3.2 Installation

SIMATIC CC7

Operating Instructions, 10/2019, C79000-G8976-C503-02

WARNING

Explosion hazard
Do not disconnect equipment when a flammable or combustible atmosphere is present.

WARNING

EXPLOSION HAZARD
The equipment is intended to be installed within an ultimate enclosure. The inner service

temperature of the enclosure corresponds to the ambient temperature of the module. Use

installation wiring connections with admitted maximum operating temperature of at least

30 ºC higher than maximum ambient temperature.

WARNING

Wall mounting is only permitted if the requirements for the housing, the installation

regulations, the clearance and separating regulations for the control cabinets or housings

are adhered to. The control cabinet cover or housing must be secured so that it can only be

opened with a tool. An appropriate strain-relief assembly for the cable must be used.

WARNING

Substitution of components may impair suitability for Division 2.

3.2

Installation

WARNING

Open equipment
The device is "open equipment" acc. to the standard UL 61010-2-201. To fulfill

requirements for safe operation with regard to mechanical stability, flame retardation,

stability, and protection against contact, the following alternative types of installation are

specified:

•

Installation in a suitable cabinet.

•

Installation in a suitable enclosure.

•

Installation in a suitably equipped, enclosed control room.

Note
You must not install the device on a wall in hazardous areas.

Содержание 6GK1411-1AC00























































































































































Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды

Siemens 6GK1411-1AC00, Руководство по эксплуатации

Результаты поиска

Содержание 6GK1411-1AC00

Отзывы:

Похожие инструкции для 6GK1411-1AC00

Бренды по названию

Популярные бренды