Siemens 6ES7647-0BA00-0YA2 Скачать руководство пользователя | Manualshive

Страница: 28 / 71

background image

SIMATIC IOT2050

28

Operating Instructions, 03/2020, A5E39456816-AA

Software and commissioning

4

Operating system and software for the SIMATIC IOT devices are freely programmable and

are downloaded from the Micro SD/eMMC card when the device is booted.
For SIMATIC IOT2050 6ES7647-0BA00-1YA2: The device starts with "Secure Boot", which

means the SD card with the customer-specific image must be signed accordingly.
Additional information on the software topics, "Secure Boot", commissioning and Micro SD

image is available in the SIMATIC IOT2000 Forum.

General information on commissioning

CAUTION

Danger of burns
The device surface can reach over 70 °C. You may get burned without any protection when

touching it.
Don't directly touch the device during its operation. Always wear protective gloves before

touching the device.
La surface de l'appareil peut atteindre une température supérieure à 70

℃

. Vous risquez

de vous brûler au contact de l'appareil si vous ne portez pas de gants de protection.
Évitez le contact direct avec l'appareil pendant son fonctionnement. Portez toujours des

gants de protection avant de toucher l'appareil.

SIMATIC IOT2000 Forum

To use the SIMATIC IOT2000 Forum, you need a login for online support.
Follow these steps to participate in the Technical Forum:
1. Open the website "Technical Forum (

http://www.siemens.com/automation/forum

2. If you do not yet have a login for online support, click "Register" at the top right of the

window and follow the registration instructions.

During registration, you enter an alias for the forum, for example. This alias is the

pseudonym under which other users can see you and talk to you in the forum.
You will receive a confirmation e-mail after registering successfully.

«
...
26
27
28
29
30
...
»

Содержание 6ES7647-0BA00-0YA2








































































Отзывы:

Нет отзывов

Похожие инструкции для 6ES7647-0BA00-0YA2

Бренд: Gallagher Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: Sollae Страницы: 38

Бренд: AES Corporation Страницы: 2

G.SHDSL.bis 4-port Security Gateway P-793H

Бренд: ZyXEL Communications Страницы: 444

Бренд: Gree Страницы: 12

Бренд: Clearswift Страницы: 21

Бренд: NavCom Technology Страницы: 7

Бренд: VBUZZER Страницы: 7

Бренд: RTA Страницы: 66

Бренд: Gainwise Страницы: 10

Бренд: RTA Страницы: 86

Бренд: AMSEC Страницы: 73

Mediatrix Model M

Бренд: Mitel Страницы: 40

Бренд: IQ Home Страницы: 21

Sure Cross Performance DX83A

Бренд: Banner Страницы: 105

PSVG-IQAN-C2E1M2W1U1

Бренд: Parker Страницы: 56

Бренд: 3onedata Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды