Siemens 6ES7144-5KD50-0BA0 Скачать руководство пользователя

Страница: 23 / 55

Parameters/address space

4.2 Parameters

Analog input module AI 4xRTD/TC 4xM12 (6ES7144-5KD50-0BA0)

Equipment Manual, 08/2020, A5E48753535-AA

Parameter

Value range

Default

Effective range with config-

uration software e.g. STEP 7

(TIA Portal)

GSD file

PROFINET IO

GSD file

PROFIBUS DP

Smoothing

•

None

•

Weak

•

Medium

•

Strong

None

Channel

Interference fre-

quency suppression

•

60 Hz (16.6 ms)

•

50 Hz (20 ms)

•

16.6 Hz (60 ms)

50 Hz (20 ms)

Channel

Diagnostics:

Reference junction

•

Disable

•

Enable

Disable

Channel

Diagnostics:

Wire break

•

Disable

•

Enable

Disable

Channel

Diagnostics

Overflow/underflow

diagnostics

•

Disable

•

Enable

Disable

---

Channel

Diagnostics:

Underflow

•

Disable

•

Enable

Disable

Channel

---

Diagnostics:

Overflow

•

Disable

•

Enable

Disable

Channel

---

Conductor re-

sistance [m

]

0 ... 50000 m

Channel

---

Hardware interrupt

high limit 1

•

Disable

•

Enable

Disable

Channel

---

Hardware interrupt

low limit 1

•

Disable

•

Enable

Disable

Channel

---

Hardware interrupt

high limit 2

•

Disable

•

Enable

Disable

Channel

---

Hardware interrupt

low limit 2

•

Disable

•

Enable

Disable

Channel

---

High limit 1

The value range depends on

the measurement type.

The value range (min./max.)

permitted for the measure-

ment type is listed in the

table 4-3

Value ranges of

the hardware interrupts

27648

Channel

---

Low limit 1

Channel

---

High limit 2

27648

Channel

---

Low limit 2

Channel

---

Interference frequency suppression: Noise at 400 Hz is automatically included in the filtering at

50 Hz.

For 2-wire connection only

Содержание 6ES7144-5KD50-0BA0
























































Результаты поиска

Содержание 6ES7144-5KD50-0BA0

Отзывы:

Похожие инструкции для 6ES7144-5KD50-0BA0

Бренды по названию

Популярные бренды

Siemens 6ES7144-5KD50-0BA0, Руководство пользователя

Результаты поиска

Содержание 6ES7144-5KD50-0BA0

Отзывы:

Похожие инструкции для 6ES7144-5KD50-0BA0

Бренды по названию

Популярные бренды