Siemens 6EP1437-3BA10 Скачать руководство пользователя страница 51

Страница: 51 / 58

Applications

9.5 Protection against short-time voltage dips

SITOP PSU8200 3ph
Manual, 11.2014, C98130-A7638-A1-2-7629

9.5

Protection against short-time voltage dips

In the case of a drop in the line-side supply voltage, the SITOP PSU8200 power supply can

still maintain the output voltage for a short time in the millisecond range (see section

Technical data (Page 29)).
For line supplies that manifest frequent brief voltage dips, in order to increase the power

supply reliability, it may make sense to increase the line buffering time in the device using an

additional SITOP PSE201U buffer module.
The SITOP PSE201U buffer module, based on electrolytic capacitors, is connected in

parallel to the 24 V power supply output (Figure 9-6 Buffering brief power failures using the

SITOP PSE201U buffer module (Page 51)). The buffer time is 200 ms at 40 A up to 1.6 s for

a load current of 5 A. This time can be increased a multiple number of times by connecting

buffer modules in parallel; the maximum buffer time is 10 s.
You can find additional information at:
SITOP PSE201U manual (

http://support.automation.siemens.com/WW/view/en/41129219

)

Figure 9-6

Buffering brief power failures using the SITOP PSE201U buffer module

Содержание 6EP1437-3BA10



























































Результаты поиска

Содержание 6EP1437-3BA10

Отзывы:

Siemens 6EP1437-3BA10, Руководство пользователя, Страница: 51 / 58

Результаты поиска

Содержание 6EP1437-3BA10

Отзывы: