Siemens 6DL1131-6TH00-0PH1 Скачать руководство пользователя

Страница: 19 / 50

Parameters

6.1

Parameter types

Definition

You can define the mode of operation of the I/O module via the parameter types, thereby
influencing the functions supported by the module.

The time stamp is configured in the configuration dialog of the I/O module.

Description

There are two types of parameters:

• Module/channel parameters (data record 128)

• System parameters (potential group, IO redundancy)

6.2

Module/channel parameters

Definition

Module/channel parameters are specific parameters whose configuration can affect the entire
module or channels.

Description

The following module/channel parameters are available:

Parameters

Value range

Default

Changing parame‐

ter settings in RUN

Efficiency range

Diagnostics, Missing sup‐
ply voltage L+ (Page 21)

• Enabled
• Disabled

Enabled

Yes

Module

IO redundancy
(Page 21)

• None
• 2 modules

None

Yes

Module

Diagnostics: short-cir‐
cuit (Page 21)

• Enabled
• Disabled

Enabled

Yes

Channel

Diagnostics: wire break
(Page 22)

• Enabled
• Disabled

Enabled

Yes

Channel

Diagnostics: change-
over contact error
(Page 22)

• Enabled
• Disabled

Disabled

Yes

Channel

DI 16xNAMUR HA
Equipment Manual, 08/2019, A5E39293880-AD

Содержание 6DL1131-6TH00-0PH1



















































Результаты поиска

Содержание 6DL1131-6TH00-0PH1

Отзывы:

Похожие инструкции для 6DL1131-6TH00-0PH1

Бренды по названию

Популярные бренды

Siemens 6DL1131-6TH00-0PH1, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6DL1131-6TH00-0PH1

Отзывы:

Похожие инструкции для 6DL1131-6TH00-0PH1

Бренды по названию

Популярные бренды