manualshive.com logo in svg

Siemens 3RB24, Руководство пользователя, Страница: 26 / 128

Поделиться
Скачать
Siemens 3RB24 Скачать руководство пользователя страница 26

⑨

Red "GND FAULT" LED:
A continuous red light signals an active ground fault trip.

⑩

Green "DEVICE/IO‑LINK" LED:
A continuous green light signals that the device is working correctly; an interrupted continuous 
light (interrupted for 200 ms every 3 s) indicates communication via IO‑Link.
Continuous red light indicates a trip or a fault.
You can find more information in Chapter "Fault codes (only in the case of non-acknowledgeable 
faults) (Page 104)" and Chapter "IO-Link diagnostics (Page 106)".

Figure 3-2

Operator controls and display elements of the evaluation module

Note

Connection of the solid-state overload relay for IO‑Link is described in Chapter "Connecting 
(Page 71)".

Product description
3.4 Operator controls and display elements

SIRIUS 3RB24 electronic overload relay for IO-Link

26

Equipment Manual, 07/2022, NEB969165602000/RS-AA/003

Содержание 3RB24

































































































































Отзывы:

Нет отзывов