manualshive.com logo in svg

Siemens 3AD8, Инструкция по эксплуатации

Поделиться
Скачать
Siemens 3AD8 Скачать руководство пользователя страница 19

19

Radio/modem interface

In order to communicate with the SCADA 
system, master station a long-haul radio or 
modem is required. The RCU electronics 
provides two digital interfaces for the radio:

  

 

Serial asynchronous data (serial 
interface)

  

 

10/100BaseT (Ethernet interface).

The Ethernet interface is not activated for software 
versions covered in this instruction manual.

Only one interface can be used at a time. 
The use of the Ethernet interface increases 
the power consumption of the RCU. A 
custom cable is required to connect the 
radio/modem to the RCU interface. The 
design and construction of this cable must 
be performed by the customer referring to 
Radio/modem interface electrical section on 
page 65, or as a value-added service 
provided by Siemens.

Figure 14: Radio/modem interfaces

Item

Description

A

Ethernet port

B

Serial port

A

B

Содержание 3AD8









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды