Siemens 1PH818 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 198

background image

4.10

Rotational speed limit values

WARNING

Excessively high speeds
Excessive rotational speed can lead to serious damage to the machine. This can result in

death, serious injury, or material damage.
● Avoid operation above the permissible speed by using the appropriate control function.
● Observe the speeds stamped on the rating plate.

4.11

System-inherent frequencies

NOTICE
System resonances
Excessive vibrations and system resonances can damage the machine set.
● Configure and match the system consisting of the foundation and machine set in such a

way that no system resonances can arise and result in the permissible vibration levels

being exceeded.

● The vibration limit values according to DIN ISO 10816-3 must not be exceeded.

4.12

Torsional loading of the drive train due to faults in the electrical supply

In the event of faults in the electrical connection during operation, excessive air gap torques

can lead to additional mechanical torsional load on the line shaft.

Note
The system planner is responsible for the entire drive train.

WARNING

Torsional loadings of the shaft assembly
If the configuration does not correctly recognize the mechanical torsional loadings of the shaft

assembly, this can lead to serious damage to the machine. This can result in death, serious

injury or material damage.
When planning the system, consider the configuration data.

Preparations for use

4.12 Torsional loading of the drive train due to faults in the electrical supply

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

35

«
...
33
34
35
36
37
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: Stobag Страницы: 40

Бренд: TAYO Страницы: 42

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Calzoni MR Series

Бренд: Parker Страницы: 50

Бренд: TecumsehPower Страницы: 24

Бренд: Tecumseh Страницы: 20

Бренд: Tecumseh Страницы: 8

Бренд: Oriental motor Страницы: 8

Бренд: Oriental motor Страницы: 12

Бренд: Arrow Shark Страницы: 16

Бренд: Jets Munt Страницы: 24

Бренд: MULTIPLEX modell Страницы: 11

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Бренд: Honda Страницы: 16

Бренд: Honda Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды