Siemens 1PH818 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 198

background image

4. Ground and short-circuit.
5. Provide protection against adjacent live parts.
To energize the system, apply the measures in reverse order.

2.3

Qualified personnel

All work at the machine must be carried out by qualified personnel only. For the purpose of

this documentation, qualified personnel is taken to mean people who fulfill the following

requirements:
● Through appropriate training and experience, they are able to recognize and avoid risks

and potential dangers in their particular field of activity.

● They have been instructed to carry out work on the machine by the appropriate person

responsible.

2.4

Safe handling

Workplace safety depends on the attentiveness, care, and common sense of the personnel

who install, operate, and maintain the machine. In addition to the safety measures cited, as a

matter of principle, the use of caution is necessary when you are near the machine. Always

pay attention to your safety.
Also observe the following to prevent accidents:
● General safety regulations applicable in the country where the machine is deployed.
● Manufacturer-specific and application-specific regulations
● Special agreements made with the operator
● Separate safety instructions supplied with the machine
● Safety symbols and instructions on the machine and its packaging

WARNING

Live parts
Electric machines contain live parts.
Fatal or severe injuries and substantial material damage can occur if the covers are removed

or if the machine is not handled, operated, or maintained properly.
● Always observe the “five safety rules" (Page 13) when carrying out any work on the

machine.

● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.
● Regularly and correctly maintain the machine.

Safety information
2.4 Safe handling

SIMOTICS M-1PH8 1PH818., 1PH822.

14

Operating Instructions 07/2016

«
...
12
13
14
15
16
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: Kärcher Страницы: 224

Бренд: O.S. engine Страницы: 21

Бренд: O.S. engine Страницы: 25

Бренд: Great Wall Страницы: 72

Бренд: Grundfos Страницы: 13

Бренд: GR Страницы: 8

2005 ENDUCROSS EC 125

Бренд: GAS GAS Страницы: 50

Powertrain 4.3 L

Бренд: GMC Страницы: 196

Бренд: Robin America Страницы: 24

Бренд: YS Страницы: 2

Бренд: Baotian Страницы: 41

Бренд: Front Runner Страницы: 15

Бренд: Mitsubishi Страницы: 219

Бренд: Yanmar Страницы: 231

Бренд: Nakanishi Страницы: 2

Бренд: Nakanishi Страницы: 2

116 - V1.1 ASSEMBLY EXHAUSTS 3207I-3208I-3210

Бренд: MVVS Страницы: 1

Бренд: Lenze Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды