SICK V200 Скачать руководство пользователя | Manualshive

Страница: 21 / 64

background image

Operating Instructions

Chapter

4

V200/V300

8012227/YT87/2016-03-29

© SICK AG • Industrial Safety Systems • Germany • All rights reserved

21

Subject to change without notice

Mounting

4.2.1

Minimum distance according to EN ISO 13

855 and EN ISO 13

857

The minimum distance as defined in EN ISO 13

855 and EN ISO 13

857 depends on the

following factors:

•

stopping/run-down time of the machine or system
(The stopping/run-down time is shown in the machine documentation or must be
determined by taking a measurement.)

•

response time of the entire protective device (V200/V300: 20 ms)

•

reach or approach speed

•

other parameters that are stipulated by the standard depending on the application

How to calculate the minimum distance S according to EN ISO 13

855 and

EN ISO 13

857:

The following calculation shows an example calculation of the minimum distance. The
calculation is based on the assumption that the approach is perpendicular to the
protective field.
Depending on the application and the ambient conditions, a different calculation may be
necessary.

⋅

Initial formula: S = K × T + 8 × (d – 14)
Where …
S = Minimum distance in [mm]
K = 2000 mm/s

Definition and value as per EN ISO 13

855, derived from data on the approach

speed of the body or parts of the body

T = Stopping/run-down time of the entire system in [s]

Stopping/run-down time of the entire system = Stopping/run-down time of the
m response time of the protective device after light path interruption

d = Detection capability (resolution) of the protective device in [mm]
The reach/approach speed is already included in the calculation formula.
With K = 2000 mm/s the 1st formula is:
1. calculation formula: S = 2000 × T + 8 × (d – 14)

⋅

If the result S is

″

100 mm and S

′

500 mm, then use the determined value as the

minimum distance.
As per EN ISO 13

855 a minimum distance S < 100 mm is not allowed. If you obtain a

value S < 100 mm with your calculation, please contact SICK service.

⋅

If the result is S > 500 mm, use K = 1600 mm/s in the formula and calculate S again:
2. calculation formula: S = 1600 × T + 8 × (d – 14)

⋅

If the new value S is > 500 mm, then use the newly determined value as the minimum
distance.
If the new value S is

′

500 mm, then use 500 mm as the minimum distance.

Example:

The following values apply:
Stopping/run-down time of the machine = 290 ms
Response time of the V200/V300 after light path interruption = 20 ms
Detection capability (resolution) d of the V200/V300 = 20 mm
You will find the values for the response time and the resolution of the V200/V300 in
chapter 11 “Technical specifications” on page 52.

Note

Note

Note

«
...
19
20
21
22
23
...
»

Содержание V200

































































Отзывы:

Нет отзывов

Похожие инструкции для V200

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 2

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 2

Бренд: GE Страницы: 85

Бренд: GE Страницы: 85

Бренд: GE Страницы: 85

Бренд: Xblitz Страницы: 64

Бренд: FourStar Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды