SICK UE4740 Скачать руководство пользователя

Страница: 30 / 44

Chapter

Operating Instructions

UE4740

8020182/1CUO/2022-08-26

Subject to change without notice

Fault diagnosis

8.3.2

Special aspects of the PROFIsafe error displays

Display

Possible cause

How to remedy the error

BUS



PROFINET IO communi-
cation with the FPLC is
established, but the safety
communication is still
inactive. The FPLC safety
program has not been
started yet



Ensure that a PROFIsafe master
has been used.



Check the state of the safety
program.



Green

Acknowledgement by the

user required. The FPLC
has recognised an error at
the EFI gateway and has
passivated the EFI
gateway



Check the PROFINET IO diagnostic
data of the EFI gateway.



Eliminate any errors.



Then acknowledge the error
elimination.



Red

General error of the
PROFINET IO, no
communication possible



Check the PROFINET IO connecting
cable.



Check that the PROFINET IO
settings in the FPLC and at the EFI
gateway agree.



Red

No valid PROFINET IO
configuration



Check that the PROFIsafe address
in the FPLC and at the EFI gateway
agree.

8.3.3

Special error displays for PROFINET IO

Display

Possible cause

Rectification of the error

BUS



Red

No communication on
PROFINET IO



Check the PROFINET IO connecting
cable.



Verify that the PROFINET IO
settings in the PLC and on the EFI
gateway correspond.



Red

Not a valid PROFINET IO
configuration



Verify that the PROFINET IO
settings in the PLC and on the EFI
gateway correspond.

Tab. 9: Special aspects of the

LED error displays of the

PROFIsafe

Tab. 10: Special LED error

displays for PROFINET IO

Содержание UE4740












































Результаты поиска

Содержание UE4740

Отзывы:

Похожие инструкции для UE4740

Бренды по названию

Популярные бренды

SICK UE4740, Руководство по эксплуатации

Результаты поиска

Содержание UE4740

Отзывы:

Похожие инструкции для UE4740

Бренды по названию

Популярные бренды