manualshive.com logo in svg

SICK TRANSIC Extractive TRANSIC151LP, Руководство по эксплуатации, Страница: 66 / 84

Поделиться
Скачать
SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 66

66

8015383/ZUQ7/V1-3/2020-06 | SICK

O P E R A T I N G   I N S T R U C T I O N S  |  TRANSIC151LP

Subject to change without notice

9

SHUTDOWN 

9

Shutdown

9.1

Safety information

●

TRANSIC151LP: Open the display cover only for operation purposes. Never open the side 
covers when voltage is switched on

.

●

TSA151 voltage supply unit: Do not open the cover when voltage is switched on! 

All safety regulations for shutdown, 

see “Safety information”, page 19

 and in Section 

Maintenance

 on 

 “Safety notes”, page 57

.

9.2

Preparations for shutdown

▸

Inform all connected locations.

▸

Passivate/deactivate the safety devices.

▸

Stop the inflow.

▸

Save the data.

9.3

Switching the TRANSIC151LP off

▸

Switch the TRANSIC151LP voltage supply off.

9.4

Protecting a shutdown TRANSIC151LP

▸

Store in a protected, dust-free and dry place. 

▸

Observe the storage temperatures, 

see “Ambient conditions”, page 74

.

9.5

Disposal

▸

The TRANSIC151LP can easily be disassembled into its components which can then be 
sent to the respective raw material recycling facilities.

▸

Dispose of the TRANSIC151LP as industrial waste.

9.6

Shipping the TRANSIC151LP to SICK

CAUTION:

Never divert the laser beam

Never insert an optical instrument into the measuring gap to possibly divert the laser 
beam whilst the TRANSIC151LP is switched on. 

▸

 

Observe the respective valid local regulations for the disposal of industrial waste.

NOTE:

Hazard through process residues on the device 

▸

Clean the TRANSIC151LP before shipping to SICK.

Содержание TRANSIC Extractive TRANSIC151LP





















































































Отзывы:

Нет отзывов