SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 84

SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 19

19

8015383/ZUQ7/V1-3/2020-06 | SICK

O P E R A T I N G I N S T R U C T I O N S | TRANSIC151LP

Subject to change without notice

INSTALLATION

3

3.2

Information on installation in potentially explosive atmospheres

3.3

Installation

3.3.1

Safety information

When using the device in potentially explosive atmospheres:

▸

Installation, start-up, maintenance and inspection should only be performed by
experienced technicians with knowledge of the relevant rules and regulations for
potentially explosive atmospheres.

WARNING:

Ex certification becomes void for unallowed power supply

▸

Only use the TSA151 voltage supply unit to run the TRANSIC151LP.

▸

Only use a 24V DC PELV power supply unit on the TSA151 voltage supply unit.

▸

Observe the “X” marking on the type plate,

see “Type code TRANSIC151LP”,

WARNING:

Toxic gases escaping

▸

Ensure the seals have been fitted and the installation is gas-tight.

WARNING:

Acids and alkalis escaping

▸

Ensure the installation is completely sealed.

Installation information: Only use SICK original accessories and spare parts,

parts and accessories”, page 62

.

WARNING:

Risk of injury through device components under pressure

▸

Only install and remove the TRANSIC151LP when free from pressure.

When necessary, provide separating elements to ensure safe installation and removal.

WARNING:

Risk of injury through components unsuitable for pressure

▸

Only use components designed for the process pressure in the application.

WARNING:

Start-up only by technicians

The TRANSIC151LP may be installed and put into operation only by technicians with
appropriate training, who, based on their training and knowledge of relevant regulations
concerning the gases used can assess and detect hazards.

NOTE:

Check the TRANSIC151LP for completeness and damage

Check the TRANSIC151LP for completeness and damage (e.g., through transport)
before start-up.

«
...
17
18
19
20
21
...
»

Содержание TRANSIC Extractive TRANSIC151LP





















































































Отзывы:

Нет отзывов