SICK IDM series Скачать руководство пользователя | Manualshive

Страница: 107 / 134

background image

Operating Instructions

Condensed Data Wizard

IDM corded & IDM Bluetooth

8017159/142O/2019-05-23

© SICK AG · Germany · All rights reserved · Subject to change without notice

107

3.12.3

Data Verifier

The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded
Data Transmitting Filter. All data must conform to the Identified Barcode Symbologies, Identified Data Length,
and one to three Identified Characters in the checking position. Otherwise, the Hand-held scanner will not
transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error
and skip the scanned data. The Data Verifier checks only scanned data without Preamble, Postamble, STX,
ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix. Regarding the “Bar Code Selection” and
“Position Calculation” of Data Verifier, please refer to page 110 and 111 for details. All “Character” input
should be referred to the ASCII/HEX Table listed in the Appendix (page 119) to find matched HEX value.

PROGRAM

F_DEFAULT

Family Code Selection

P.C.

Parameter Selection

1

st

Option Code

2

nd

Option Code

Verifier Control

SS Disable



FIN

MS

Select one barcode symbology

(2 digits)

Automatic termination

MS

Select all barcode symbologies

00

Automatic termination

Identified Data Length

SS Disable



FIN

DS

Enable

(2 digits)

Determine the identified data length

for verification.

1st identified character

SS Disable



FIN

DS

Enable

Position: (2 digits)

[00-7F]

Define position (refer

to chapter 3.12.7)

1 character

2nd identified character

SS Disable



FIN

DS

Enable

Position: (2 digits)

[00-7F]

Define position (refer

to chapter 3.12.7)

1 character

3rd identified character

SS Disable



FIN

DS

Enable

Position: (2 digits)

[00-7F]

Define position (refer

to chapter 3.12.7)

1 character

«
...
105
106
107
108
109
...
»

Содержание IDM series







































































































































Отзывы:

Нет отзывов

Похожие инструкции для IDM series

Бренд: Datalogic Страницы: 5

Бренд: Moneris Страницы: 25

Бренд: Franklin Страницы: 28

Бренд: Metrologic Страницы: 66

DRS-50 Translingual

Бренд: SMART Страницы: 12

PowerScan PD953X

Бренд: Datalogic Страницы: 40

Бренд: Denver Страницы: 36

OBID i-scan ID ISC.MRU102-POE

Бренд: Feig Electronic Страницы: 21

Бренд: Creator Страницы: 16

Linea-PRO 4 MSR

Бренд: Infinite Peripherals Страницы: 24

Бренд: Dormakaba Страницы: 28

PowerScan M8300

Бренд: Datalogic Страницы: 24

Бренд: Meec tools Страницы: 53

Бренд: AuthenTrend Страницы: 17

Бренд: Shift3 Страницы: 33

Shuttle SG-15 COLOUR

Бренд: Scantech Страницы: 91

Бренд: Scantech Страницы: 121

Fastmark 600 Series

Бренд: AMT Datasouth Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды