SICK GM32 Series Скачать руководство пользователя страница 32

Страница: 32 / 80

8012707/ZVF9/V2-1/2019-04 | SICK

O P E R A T I N G I N S T R U C T I O N S | GM32

Subject to change without notice

START-UP

4.7

For the GPP probe: Electrical connection

Unscrew and take off the purge air fixture cover.

Check the switch setting for swapping the voltage to the available power voltage and
correct when necessary.

Fig. 14: Switch to select voltage and fuses

Check the fuses according to the available power voltage and replace when necessary.

Connect the power supply to the power voltage.
Line with three wires:
– Green-yellow: PE A protective conductor must be connected.
– Blue: N
– Brown: L1

Fuse holder

Switch to set voltage

NOTE: The fuses depend on the available power voltage.

▸

Only use the correct fuses.
– 230 V: 1.6 A (slow)
– 115 V: 2.5 A (slow)

NOTE: Danger of condensation

The GPP probe must have reached its operating temperature before being inserted
in the gas duct.

▸

First fit the GPP probe during final installation in the gas duct,

see “Installing the

measuring probe in the gas duct”, page 34

▸

Attach clearly visible warnings against accidental switching-off to all switching
devices where the GPP probe heater can be switched off.

Содержание GM32 Series

















































































Результаты поиска

Содержание GM32 Series

Отзывы:

Похожие инструкции для GM32 Series

Бренды по названию

Популярные бренды

SICK GM32 Series, Руководство по эксплуатации

Результаты поиска

Содержание GM32 Series

Отзывы:

Похожие инструкции для GM32 Series

Бренды по названию

Популярные бренды