SICK D 35 Series Скачать руководство пользователя страница 13

Страница: 13 / 68

8014868/YIF1/2020-10-19 • © SICK AG • Subject to change without notice 13

Safety

2.3

Requirements for skilled persons and operating personnel

WARNING!

Risk of injury due to insufficient training!

Improper handling may result in considerable personal

injury and material damage.
For this reason:
• All work must only ever be carried out by the stipulated

persons.

The operating instructions state the following qualification requirements for

the various areas of work:
•

Qualified personnel

are able to carry out the work assigned to them and independently

recognize potential risks due to their specialist training, knowledge, and

experience, as well as knowledge of the relevant regulations.

•

Electrical specialists

are able to carry out work on electrical systems and independently

recognize potential risks due to their specialist training, knowledge, and

experience, as well as knowledge of the relevant standards and regula-

tions.

The electrician must comply with the provisions of the locally applicable

work safety regulation.

2.4

Warning symbol on the device

Laser class 2

Distance sensors with a class 2 laser according to EN/IEC60825-1:2014

(identical laser class for issue EN/IEC 60825-1:2007) carry the following

warning label.

LASER APERTURE

MAX. OUTPUT ≤ 250mW

PULSE LENGHT = 4ns

WAVELENGHT = 658nm

EN/IEC 60825-1:2014

Complies with 21 CFR

1040.10 and 1040.11

except for deviations

pursuant to laser notice

No. 50, dated June 24, 2007

LASER

• Laser output aperture label,

→

See Fig. 5 on page 17

• CAUTION LASER RADIATION

Do not look into the beam.

Laser class 2 product

•

Specification of maximum output

power, pulse length, wavelength

• EN/IEC 60825-1:2014:

Complies with 21 CFR 1040.10

and 1040.11 except for tolerances

according to Laser Notice No. 50

dated 24/06/2007

Fig. 1: Warning symbol on sensor with class 2 laser

Содержание D 35 Series





































































Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды

SICK D 35 Series, Руководство по эксплуатации

Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды