SICK CLV62x Скачать руководство пользователя

Страница: 33 / 40

Online Help

Chapter

Barcode Scanner CLV62x

CLV62x

8011967/S345/2008-04-23

Serial auxiliary interface

The aux interface is configured with the parameters of the

Serial auxiliary interface

group.

PROFIBUS DP Gateway

The PROFIBUS DP interface is configured with the parameters of the

PROFIBUS DP Gateway

group.

DeviceNet Gateway

The DeviceNet interface is configured with the parameters of the

DeviceNet Gateway

group.

2.2.5.2 Ethernet

The Ethernet interface provides the reading result for further processing by the host com-
puter.

General

The network settings of the scanner are set via the parameter of the

General

group. These

settings must be defined by the network administrator.

Parameter

Function

Protocol / Output format

Define the output of the auxiliary interface.

Activate heartbeats

Activate the output of a regular heartbeat.

Heartbeat interval

Enter time between two heartbeats.

Restart interval on sending

Restart interval after the output of a reading result.

Gateway

Activate PROFIBUS DP interface or DeviceNet respectively.

Parameter

Function

Use device ID as profibus
address

Activate/deactivate the scanner's device ID as profibus address.

Device ID

The device ID of the scanner is displayed.

Operating mode

Select the profibus protocol.

Parameter

Function

Use device ID as DeviceNet
address

Activate/deactivate the scanner's device ID as DeviceNet
address.

Address

Enter the device address in DeviceNet.

Operating mode

Select the DeviceNet protocol.

Baudrate

Select speed of DeviceNet interface.

Length of input-data

Enter the length of the input data.

Length of output-data

Enter the length of the output data.

Hint

The scanner has to be restarted after modification of one of this group parameters.

Parameter

Function

IP address

Enter IP address of scanner.

Subnet mask

Enter subnet mask of scanner.

Default gateway

Enter default gateway of scanner.

Speed

Select network speed.

MAC address

Enter MAC address of scanner.

Содержание CLV62x







































Результаты поиска

Содержание CLV62x

Отзывы:

Похожие инструкции для CLV62x

Бренды по названию

Популярные бренды

SICK CLV62x, Онлайн руководство пользователя

Результаты поиска

Содержание CLV62x

Отзывы:

Похожие инструкции для CLV62x

Бренды по названию

Популярные бренды