≥
750mm
580mm
557mm
7
47 m
m
5
m
00
m
38mm
Ventilation
slot
>
30
mm
Turn off the mains to the equipment before carrying out any maintenance and wait for it cool
Never use abrasive products. Rinse the stainless steel elements with water and
soft cloth. Use sponges or a moist cloth to clean the tops, and remember that water in excess
vinegar. Clean the electric tops using a moist cloth,
warm. Only licensed repairers should service the appliance.
After use, a discolouration of the stainless steel hot plate rims is to be expected and
Appliances with three-pole cable are set up for operation with alternating current at the voltage
the rating plate Look at the connection wiring diagram. The earth
The connection to the electricity supply must be made by a qualified
When the appliance is to be installed above a
Cleaning
elements. Clean tough stains using non abrasive detergents, or warm
Important Notice
This does not effect its operation.
Installation
Electrical connection
down. We advise using lukewarm water and detergents to clean enameled elements. Never
dry using a
can damage the electric
then lightly oil the the top when it is still
cannot be avoided.
and frequency indicated on
conductor is yellow/green.
person and following the regulations in force.
built-in oven, the two appliances must be connected separately.
The supply cable must be so positioned that no point can reach a temperature 50° C higher
Also check that the supply system has an effective earth connection
easily when the appliance is installed.
Fitting guidelines
The voltage rating of the hob heating elements is 220-240V
.
Adapting the cooker to operate.
to the connection diagram below. The connection diagram is also
connection box. Remember that the connection wire should match the connection type and
The connection cable must be secured in a strain-Relief clamp.
Caution!
Remember to connect the safety circuit to the connection box terminal marked with
cut off in case of emergency. The distance between the working
switch must be at least 3 mm. Before connecting the cooker to the power supply it is
important to read the information on the data plate and the connection diagram.
The manufacturer refuses all responsibility if the standards in force are not respected.
CONNECTION DIAGRAM
Caution! Voltage of heating elements 220-240V
Caution! In the event of any connection the safety
Wire must be connected to the
E terminal.
Recommended
type of
connection
lead
For 220-240V earthed one-phase
connection, bridges connect L
terminals and terminals, safety
wire to
N
L
E
H05VV-F3G2.5
N
L
N
than ambient temperature.
and corresponds to the standards in force and that the plug (or omnipolar switch) can be reached
With one - phase current is possible by appropriate bridging in the connection box according
found on the cover of the
the power rating of the cooker
.
The electricity supply for the hob must have a safety switch which enables the power to be
contacts of the safety
TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL:
This appliance must be installed only by authorised personnel and in accordance with
of sustaining temperatures of 80 degrees Celsius. All
surfacing materials should be certified suitable for this temperature.Do not instal it in l
the unfire-resistant place (like curtain etc). When you operate, the manufacturer has no
According to the picture as follows, cut the square hole in bench and place the built-in electric
hob in it. Your hob can be fitted to any worktop with a thickness of 40 to 50 mm.
the regulations of Electricity authorities. The wall and bench surfaces must be capable
laminates, fixing adhesive and
responsibility.
Note 1 :
Fire resistant material (eg ceramic tiles) is required to 450 mm above burner top if wall or
vertical structures are not permitted within 200 mm from burner.
Note 2:
No overhanging surface or rangehood and exhaust system are not permitted within 750 mm
Note 3:
Leave at least 50 mm clearance between the base of the appliance and a combustibile surface.
Never leave the packing components (plastic bags, nails, foamed polystyrene, etc..) within
the reach of the children since they are a source of potential danger.
above burner tops.
MALFUNCTION ELIMINATION
Malfunction
Eliminating guide
Electric hob doesn't work
Check the connection of wires
Check the fuse and the current limit
There is some smoke
when it is working
•
It is normal the first time you use.
•
Clean the drail around the electric hob
and the heating area.
The
wire is damaged
•
Connect the nearest maintainance center to
change the equipment parts.
•
••
Symbol
Value
Unit
Model identification
Type of hob
Number of electric cooking
zones and/or areas
Heating technology (induction
cooking zones and cooking
areas, radiant cooking zones,
solid plates)
For circular cooking zones or
area: diameter of useful surface
area per electric heated cooking
zone, rounded to the nearest 5 mm
For non-circular cooking zones or
areas: length and width of useful
surface area per electric heated
cooking zone or area, rounded to
the nearest 5 mm
Energy consumption per cooking
zone or area calculated per kg
Energy consumption for the
hob calculated per kg
Ø
L, W
--
--
--
--
EC
electric cooking
EC
electric hob
Built-in hob
4
FL: 18,0 cm
N/A
FR: 14.5 cm
FL: 199.5
RR: 194.5
FR/RL: 184.5
RR: 18,0 cm
RL: 14.5 cm
cm
cm
Wh/kg
Wh/kg
190.75
About Erp
Solid plates
5
6
7
8
PHP601SS
