Shuttle ME62 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 79

background image

- 63 -

Onboard FDC Controller

This item specifices onboard floppy disk drive controller. This setting
allows you to connect your floppy disk drives to the onboard floppy
connector. Choose the "Disabled" settings if you have a separate
control card.

The choice: Enabled, Disabled.

Onboard Serial Port1/Port2

This item is used to define onboard serial port 1 / port 2 to 3F8/IRQ4,
2F8/IRQ3.

UART Mode Select

The main board support IrDA (HPSIR) and Amplitudes Shift Keyed IR
(ASKIR) infrared through COM2 port. This item specifies onboard
Infra Red mode to IrDA 1.0, ASKIR, MIR 0.57M, MIR 1.15M, FIR or
Standard (Disabled).
Note : FIR is not available currently.

RxD, TxD Active

This item specifies the Active level for RxD & TxD signal.

The choice: Hi,Lo , Lo,Hi , Lo,Lo , Hi,Hi.

IR Transmission Delay

This item enabled/disabled the delay of the IR state change from Rx
to Tx mode or Tx to Rx mode.

UR2 Duplex Mode

This item specifies onboard infrared transfer mode to full-duplex.
This item will not show up when IrDA, ASKIR, or MIR UR2 modes
are selected.

Use IR Pins

This item select the InfraRed module pin out.

Onboard Parallel Port

This item specifies onboard parallel port address to 378H, 278H,
3BCH or Disabled.

Parallel Port Mode

This item specifies onboard parallel port mode. The options are SPP,
EPP, ECP, and EPP+ECP.

«
...
63
64
65
66
67
...
»

Содержание ME62
















































































Отзывы:

Нет отзывов

Похожие инструкции для ME62

Бренд: Ublox Страницы: 23

Бренд: ASROCK Страницы: 5

Z690 Phantom Gaming 4

Бренд: ASROCK Страницы: 109

Бренд: Biostar Страницы: 85

Бренд: Gigabyte Страницы: 31

Бренд: Biostar Страницы: 51

Бренд: R&S Страницы: 44

GA-AX370M-Gaming 3

Бренд: Gigabyte Страницы: 40

Бренд: Emcore Страницы: 12

PCAN-MicroMod Evaluation Kit

Бренд: Peak Страницы: 18

Бренд: Microchip Technology Страницы: 44

Бренд: WynMax Страницы: 68

Бренд: Biostar Страницы: 37

Бренд: Microsemi Страницы: 22

Бренд: Intel Страницы: 87

Бренд: A-Trend Страницы: 44

AR6MXCS- Series

Бренд: BCM Страницы: 9

Бренд: AOpen Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды