Shuttle AN50R Скачать руководство пользователя

Страница: 68 / 76

- 64 -

Onboard SuperIO Device

Press <Enter> to enter the sub-menu of detailed options.
Onboard FDC Controller
This item specifices onboard floppy disk drive controller. This setting
allows you to connect your floppy disk drives to the onboard floppy
connector.

The choice: Enabled or Disabled.

Onboard Serial Port 1
The option is used to assign the I/O address and interrupt request (IRQ)
for the onboard serial port 1 (COM1).

The Choice: Disabled, 3F8-IRQ4, 2F8-IRQ3, 3E8-IRQ4, 2E8-IRQ3,

or Auto.
Onboard Infrared Port
The option is used to assign the I/O address and interrupt request (IRQ)
for the onboard Infrared Port.

The Choice: Disabled, 3F8-IRQ4, 2F8-IRQ3, 3E8-IRQ4, 2E8-IRQ3,

or Auto.
UART Mode Select
This item allows you to select an operating mode for the IrDA infrared.

The choice: Normal, IrDA, ASKIR, or SCR.

UR2 Duplex Mode
This item allows you to select the IR half or full duplex function.

The choice: Full or Half.

Onboard Parallel Port
Allows you to determine an I/O address and interrupt request (IRQ) for
the onboard parallel port.

The choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, or Disabled.

Parallel Port Mode
Select an operating mode for the onboard parallel port. Select SPP
unless you are certain your system supports other modes.

The choice: SPP, EPP, ECP, or ECP+EPP.

ECP Mode Use DMA
When the parallel port mode is set to ECP, this item becomes seletable.

The choice: 1 or 3.

Содержание AN50R













































































Результаты поиска

Содержание AN50R

Отзывы:

Похожие инструкции для AN50R

Бренды по названию

Популярные бренды

Shuttle AN50R, Руководство пользователя

Результаты поиска

Содержание AN50R

Отзывы:

Похожие инструкции для AN50R

Бренды по названию

Популярные бренды