Shuttle AB52P Скачать руководство пользователя | Manualshive

Страница: 70 / 76

background image

- 67 -

IRQ Resources

When resources are controlled manually, assign each system interrupt a
type, depending on the type of device using the interrupt.
IRQ3/4/5/7/9/10/11/12/14/15 assigned
This item allows you to determine the IRQ assigned to the ISA bus and
is not available to any PCI slot. Legacy ISA for devices is compliant with
the original PC AT bus specification; PCI/ISA PnP for devices is compli-
ant with the Plug-and-Play standard whether designed for PCI or ISA
bus architecture.

Ø

The choice: PCI Device or Reserved.

PCI/VGA Palette Snoop

This item is designed to overcome problems that can be caused by
some nonstandard VGA card. This board includes a built-in VGA
system that does not require palette snooping so you must leave this
item Disabled.

Ø

The choice: Enabled or Disabled.

Assign IRQ For USB

Names the interrupt request (IRQ) line assigned to the USB on your
system. Activity of the selected IRQ always awakens the system.

Ø

The choice: Enabled or Disabled.

INT Pin 1/2/3/4/5/6/7/8 Assignment

Names the interrupt request (IRQ) line assigned to PCI 1 throught PCI 8
on system. Activity of selected PCI slot awakens system.

Ø

The choice: Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, or 15.

«
...
68
69
70
71
72
...
»

Содержание AB52P













































































Отзывы:

Нет отзывов

Похожие инструкции для AB52P

Бренд: Acer Страницы: 12

Бренд: Telit Wireless Solutions Страницы: 5

Бренд: SOLTEK Страницы: 72

Бренд: Biostar Страницы: 27

Advanced Socket 370

Бренд: BCM Advanced Research Страницы: 38

Бренд: Texas Instruments Страницы: 21

Advance 10T Series

Бренд: QDI Страницы: 74

Бренд: Gigabyte Страницы: 36

Бренд: Texas Instruments Страницы: 44

Бренд: Liantec Страницы: 4

Бренд: TRIGEM Страницы: 17

Бренд: ASROCK Страницы: 125

Бренд: DataExpert Страницы: 44

Бренд: DFI Страницы: 24

Бренд: DFI Страницы: 76

Бренд: IEI Technology Страницы: 161

Бренд: DEMOAC Страницы: 17

Бренд: Connect Tech Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды