Shundaiwa DGA20EM Скачать руководство пользователя страница 23

Страница: 23 / 52

(2) Operation Check

Before operating the generator, check always

if the device can work.

Ensure that the breakers and the

Switches of loads are positioned

to OFF.

Ensure every breaker to set OFF.

Refer to

『

4-2.Operation Panel

』

and

『

4-3.Output Panel

』

Following the procedure in 9-1,
Initialization and Preparation,start an engine.

Turn every breaker and ELCB to ON.

Push the RESET (Green) button on

the 1-Phase ELCB.

Confirm the red lamp on the 1-Phase

ELCB turned ON and the indicator on

the 3-Phase ELCB turns RED display.

Push the TEST button (Yellow) on 3-Phase

ELCB.

Indicator changes to Green from RED

and ELCB trips to OFF, Which shows

NORMAL.

Push the TEST button (Blue) on 1-Phase ELCB.

Red lamp turns to OFF and ELCB trips to OFF,

Which shows NORMAL.

In the event you cannot complete every step of the above procedure to the end,

the device is out of order. Consult with our authorized distributor or our engineering

section and ask to repair.

WARNING : Electric Shock / Injuries



Before turning Breaker or ELCB to ON position,

ensure that the breakers or the switches of loads are positioned to OFF.
You should communicate well with the electrician by the load side

when operating Breaker or ELCB.

Test button (Yellow)

Indicator

3-Phase ELCB

RESET button (Green)

TEST button (Blue)

Lamp

1-Phase ELCB

Main Breaker

3-Phase Breaker

1-Phase Breaker

Battery Isolator

Содержание DGA20EM





















































Результаты поиска

Содержание DGA20EM

Отзывы:

Бренды по названию

Популярные бренды

Shundaiwa DGA20EM, Руководство владельца и оператора

Результаты поиска

Содержание DGA20EM

Отзывы:

Бренды по названию

Популярные бренды