english
• Set the sliding switch for automatic
operation to "ON/AUTO" .
The "READY" display glows .
• Feed in the paper to be shred,
however, never feed in more
than 10 sheets at a time .
The cutting device starts auto-
matically, pulls in the paper and
shreds it .
When the feed opening is
clear of paper again, the cutting
device switches off .
• the cutting device runs constantly if
you set the sliding switch to "fWD" .
REV
FWD
ON/AUTO
REV
FWD
ON/AUTO
4 Operation
Paper jam
• Set the slider switch to "rev".
Pa per is pus hed out .
• Set the slider switch to "on/aUto"
again .
• do not feed in too many sheets at
once .
Shredded material container
Check the level of shredded material in the bin
frequently. empty before it becomes too full
or the cutting ability of the machine could be
compromised .
For all other malfunctions, check whether the
cutting head was correctly positioned on the
shredded material container before contacting
our customer service . If the motor was over-
loaded, let the shredder cool down for 15 to
20 minutes before using it again .
REV
FWD
ON/AUTO
5 Troubleshooting
Switch off the shredder and pull out the power
plug .
When cleaning only use a soft cloth and a mild
soap-water solution. However, no water must
enter the equipment.
6 Cleaning
8. Disposal / Recycling
Electrical and electronic old devices
contain a variety of valuable materi
als,
but also hazardous substances which
were required for function and safety.
Incorrect disposal or handling can be
dangerous to your health and the
environment . Never dispose of old devices in
the household waste . Observe the current
applicable regulations and use the collection
points for returning and recycling electric and
electronic devices . Dispose of all the packaging
materials also in an environmentally-responsi-
ble way .
7. Cleaning Photo Eye Sensors
shredstar
®
8
5/2012
• Unplug your machine – for your safety
• lift cd flap on machine(if no flap installed,
disregard this line and continue on)
Note: In the center of the paper slot you should
see 2 transparent squares – one on either side
of the slot
• Use compressed air or take a dry tissue or
paper towel and wipe back and forth a few
times just to dust that area off
• replace flap if necessary
• Plug machine back in
Shredstar_S10_manual_2012_37.indd 8
7/5/2012 1:20:30 PM
Содержание S10
