SHOWTEC 42542 Скачать руководство пользователя страница 9

 

 

 

8 

 

  

 

 

Accent Spot SW 

Product code: 42542 

 

Attention 
Before each use, examine the device visually for any defects. 

Make sure that: 

 

All screws used for installing the device or parts of the device are tightly fastened and are not 
corroded. 

 

The safety devices are not damaged. 

 

There are no deformations on housings, fixations and installation points. 

 

The lens is not cracked or damaged. 

 

The power cables are not damaged and do not show any material fatigue. 

 

Attention 
Do not expose the device to conditions that exceed the rated IP class conditions. 

This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater 
than 12 mm, such as fingers, and no protection against harmful ingress of water. 

 

Requirements for the User 

This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. 
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite 
dealer for more information. 

Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled 
person, for specific tasks and work activities associated with the installation, service and maintenance of 
this product, so that they can identify risks and take precautions to avoid them. 

Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards 
associated with the installation, service and maintenance of this product. 

Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons 
include not only users of the product but also any other persons that may have access to the device or 
who may be in the vicinity of the device. 

 

 

Содержание 42542





































Отзывы: