Shopsmith 330002 Скачать руководство пользователя

Страница: 12 / 12

MKV TABLE SYSTEM RETRO KIT - 500 TO 510

555135

6530 Poe Avenue
Dayton, Ohio 45414

845240

Rev A

03/05

2005 Shopsmith, Inc.

Printed In U.S.A.

Troubleshooting Guide

Dust Collector problems usually have simple solutions. Under normal use, you should rarely

have to service your Dust Collector. Most problems can be corrected by maintenance or a

change of work habits.

Maintenance and Troubleshooting

Problem

Probable Cause

Unit will not start.

Motor stops and starts er-

ratically

Dust blowing out around fil-

ter hood or bag

Loss of airflow

Filter hood or collection bag

blows off main housing when

Dust Collector is turned on.

Plug loose in outlet.
Defective switch.
Defective motor.
Tripped circuit breaker or blown

fuse.
Long extension cord, insufficient

wiring or on same circuit as

Shopsmith Mark V or other ma-

chinery.

Solution

Check plug and outlet.
Replace switch.
Replace motor.
Reset circuit breaker or replace

fuse.
Refer to “Electrical Require-

ments” in the Safety section.

Electrical short in cord.
Electrical short in switch.
Plug loose in outlet.

Loose retaining strap.

Filter hood clogged.
Plugged hoses, extension wands or
attachments.

Strap is tightened on top of rib on

main housing.

Replace power cord.
Replace switch.
Check plug and outlet.

Tighten retaining strap.

Dislodge dust buildup.
Unplug affected part(s).

For filter hood, tighten strap be-

tween ribs.
For collection bag, tighten strap

on flat area between rib & main

housing.

When you contact us, please tell us your Customer

Number and Date Code of your equipment. (Your cus-

tomer number appears on the invoice and mailing labels

of the literature we send to you. The date code is located

on the serial label sticker on your machine). To keep them

handy, please write in the alloted spaces below.

NOTE

If you have any questions about your Shopsmith

MARK V Lift Assist, please call our Customer

Service Department TOLL-FREE at 1-800-762-

7555, send us an e-mail at

[email protected], visit our webside

at www.shopsmith.com, or write to us at:

Shopsmith, Inc., Attn: Customer Service Tech-

nical Dept., 6530 Poe Avenue, Dayton, Ohio
45414.

Customer No.

Date Code:

Содержание 330002













Результаты поиска

Содержание 330002

Отзывы:

Похожие инструкции для 330002

Бренды по названию

Популярные бренды

Shopsmith 330002, Руководство пользователя

Результаты поиска

Содержание 330002

Отзывы:

Похожие инструкции для 330002

Бренды по названию

Популярные бренды