(Not standard with all models)
The cartridge filter can be used for wet or dry pick-up; instal-
lation is the same for both. When picking up large quantities
of liquid please refer to the Wet Pick-Up Operation section
in this manual. Use the cartridge filter in position over the
lid cage for most general dry material pick-up. With the
tank cover in an upside down position, slide the cartridge
filter down over the lid cage, pushing until the filter seals
against the cover
(Figure 12)
. Place filter retainer into the
top of the cartridge filter, hold the tank cover with one hand,
turn the handle on the filter retainer clockwise to tighten,
locking the filter into place
(Figures 13 & 14)
. To remove
the filter for cleaning, again hold the tank cover and turn
the filter retainer counter-clockwise to loosen and remove,
slide the cartridge filter off the lid cage
(Figures 15 & 16)
.
To clean the cartridge filter shake or brush off excess dirt or
rinse (from the inside of the filter) with water, dry completely
(approximately 24 hours) and re-install.
(Figures 17 & 18)
.
Note:
If the filter has been used for wet pick-up, it must be
cleaned and dried before using for dry pick-up.
WET PICk-UP OPERATION
Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of conver-
sion when going from dry to wet pick-up. Remove all dry use filters from the vacuum. A clean
cartridge filter may be used for vacuuming small amounts of liquids. for proper installation of
the cartridge filter refer to Installing the Cartridge filter. for best results when vacuuming large
quantities of liquid, remove the cartridge filter. When vacuuming liquids containing debris, it is
recommended purchasing a foam sleeve and install over filter cage; otherwise a foam sleeve
is not required for wet pick up. foam sleeve and additional filters may be purchased by visiting
our website at www. shopvac.com, contacting our customer service department, or purchasing
at your local Shop-Vac
®
distributor.
Misting in exhaust air may occur if the filter becomes saturated during wet pick-up. If misting
occurs, remove filter and allow to dry or, replace with another dry filter to eliminate the misting
and possible dripping of liquid around the lid. Turn the unit off immediately upon completing a
wet pick-up job or when tank is full and ready to be emptied. Raise the hose to drain any excess
liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place
tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid
cage.
2. Shake excess dust off foam sleeve with a rapid up and down movement.
3. hold foam sleeve under running water for a minute or two, rinsing from the inside. A water
wash is not always required, depending on the condition of the foam sleeve.
4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The
foam sleeve is now ready to to be reinstalled on the lid cage.
NOTE:
WET PICK-UP ACCESSORIES ShOULD BE WAShED PERIODICALLY, ESPECIALLY AfTER
PICKING UP WET, STICKY KITChEN ACCIDENTS. ThIS CAN BE ACCOMPLIShED WITh A WARM
SOLUTION Of SOAP AND WATER.
EMPTYING LIQUID WASTES FROM THE TANk
Your Shop Vac® Wet/Dry vacuum may be emptied of liquid waste by removing the tank cover.
To empty, stop the motor and remove the plug from the wall receptacle. Remove the tank
The vacuum is equipped with an automatic suction shut-off that operates when picking up
liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself
against a seal at the intake of the motor, shutting off suction. When this happens, the motor will
develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs,
turn unit off immediately. failure to turn unit off after float rises and shuts off suction will result
in extensive damage to the motor. To continue use, empty the liquid waste from the tank as
outlined in the previous paragraph.
NOTE:
If ACCIDENTALLY TIPPED OVER, ThE VACUUM COULD LOSE SUCTION. If ThIS OCCURS,
PLACE VAC IN UPRIGhT POSITION AND TURN SWITCh Off. ThIS WILL ALLOW ThE fLOAT TO
RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE OPERATION.
AUTOMATIC SUCTION SHUT-OFF
LUBRICATION
No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.
Trouble
Possible Cause
Remedy
Suction weakens or
cleaner runs hot
Clogged filter
Brush dirt from filter. If condition continues,
change filter.
Air leak
Check all fittings for tight fit (nozzles, hose, etc.)
Check that tank cover is sealed properly.
Obstruction in hose
or nozzle.
Check nozzle, hose, etc. for obstructions, and
remove if present.
Misting in the
exhaust air
Saturated filter
Replace saturated filter with a dry filter.
Mounting ring
falling off
foam sleeve
incorrectly positioned
Position foam sleeve on the outside of
groove around lid cage.
TROUBLESHOOTING
WARNING
– IF ANY OF THE MOTOR HOUSING PARTS
SHOULD BECOME DETACHED OR BROkEN, EXPOSING THE MOTOR OR ANY
OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE DISCONTINUED
IMMEDIATELY TO AVOID PERSONAL INJURY OR FURTHER DAMAGE TO THE
VACUUM. REPAIRS SHOULD BE MADE BEFORE REUSING THE VACUUM.
INSTALLING THE CARTRIDGE FILTER
STORAGE
Before storing your vacuum cleaner the tank should be emptied and cleaned. The power cord can
be wound around the housing of the unit for convenience
.
Accessories may be stored in the tool
holder
(not standard on all models)
so they can be readily available.
The vacuum should be
stored indoors.
12
13
14
15
16
18
17
THREE YEAR HOME USE WARRANTY
Your Shop-Vac® vacuum cleaner is warranted for normal household use, in accordance with
the User Manual, against original defects in material and workmanship for a period of three
years from date of purchase. Should this product be used for commercial or rental use, a 90
day limited warranty will apply. Shop-Vac Corporation warrants placing this vacuum cleaner in
correct operating condition, by repair or parts replacement, during the warranty period, without
charge. This warranty does not cover accessories. Use of non-recommended filters and/or
accessories may void the manufacturer's warranty. Shop-Vac® assumes no responsibility
for damage or faulty performance caused by misuse, careless handling, and where repairs or
modifications have been made. Do not attempt to service your vacuum beyond that described
in the User Manual. Proof of purchase date is required. The warranty gives you specific legal
rights, and you may have other rights which vary from state to state or province to province.
This warranty is void outside of the United States and Canada.
Customers in the United States: for product service contact Shop-Vac Corporation, Customer
Service, at (570) 326-3557 or go to www.shopvac.com/support. Visit www.shopvac.com for
your vacuum's parts list schematic.
1. Grasp cardboard collar firmly and
slide rubber guard onto inlet fitting, as
firmly as possible
(Figure 19)
.
2. When securely in place, expand and
position bag down inside of tank
(Figure 20)
.
3. Use for DRY PICK-UP only.
WARNING
– THIS VACUUM CLEANER FILTER BAG
SHOULD ONLY BE USED FOR COLLECTING DRY DIRT AND DEBRIS, SAW-
DUST, WOOD CHIPS ETC. TO AVOID HEALTH HAzARDS FROM VAPORS
OR DUST, DO NOT USE FILTER TO VACUUM TOXIC, CARCINOGENIC OR
OTHER HAzARDOUS MATERIALS SUCH AS ASBESTOS, PESTICIDES OR
OTHER HEALTH ENDANGERING MATERIALS.
Keep filters clean. Efficiency of the vacuum is largely dependent on the filters. A clogged filter
can cause overheating and possibly damage the cleaner. Check filters periodically and replace
as required. Replace with manufacturer recommended filter bag.
INSTALLING THE DISPOSABLE
FILTER BAG
19
20
cover and deposit the liquid waste contents in a suitable drain. After the tank is empty, return
the cover to its original position. To continue use, plug the cord into the wall receptacle and
start the motor.
