¼
¼
½
¾
2
4
3
5
1
2
3
4
5
2088100
9356000
1503999
6401299
1300199
Metal tank handle
Side tank handle
#10 x ¾” Screw hex head
Bolt ¼-20 x ½”
¼ - 20 Hex nut
ITEM
DESCRIPTION
PART NO.
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that the bottom is facing up.
2. Place one cotter pin in one end of the axle
(Figure 1)
.
3. Slide on one washer
(Figure 2)
.
4. Slide wheel onto axle next to washer
(Figure 3)
. Be sure flat side of wheel hub is facing outward.
5. Slide dolly next to wheel through holes provided in dolly
(Figure 4)
.
6. Slide remaining wheel, then washer onto axle end
(Figure 5)
.
7. Insert cotter pin into the remaining hole in the axle to hold wheel in place
(Figure 6)
.
8. With a pair of scissors, trim the enclosed template to fit your size tank. Sizes will be 11”, 14” or 16” diameters.
9. Once template is cut out, place on bottom of tank, align inlet arrow on template with center of inlet on tank
(Figure 7)
.
10. Align cutouts in center of rear dolly with bars on template
(Figure 8)
.
11. Place groove of rear dolly over rim of tank and push until the dolly is tight against bottom of tank
(Figure 9)
.
12. Secure dolly with screw and washer provided
(Figure 10)
.
13. If caster feet are attached together, separate by removing webbing.
14. Take caster foot marked with the letter A and align arrow on foot
(Figure 11)
with arrow on template also marked with the letter A
(Figure 12)
.
15. Place groove of foot over rim of tank and push until the caster foot is tight against bottom of tank
(Figure 13)
.
16. Secure foot with screw and washer provided
(Figure 14)
.
17. Repeat steps 14-16 with foot B.
18. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and twisting motion until casters snap into place
(Figure 15)
.
19. Place tool basket
(not standard with all models)
, with curved surface against tank, on rear wheel dolly assembly
(Figure 16)
.
CARRIAGE HANDLE ASSEMBLY
Be sure to spread ends of carriage handle when assembling to prevent
damage to tank. Attach carriage handle to tank by inserting bolt through
the center hole of handle and tank, secure with nut provided. Attach
side handles with screws provided
(Figure 17)
.
17
INSTALLING FOAM SLEEVE AND REUSABLE DRY FILTER
•
NOT STANDARD ON ALL MODELS
WARNING -
ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING
THE TANK COVER.
To pick up dust and dry material, you must install foam sleeve and reusable dry filter to ensure proper filtration. Remove inlet deflector from the
deflector guide, located on the inside of tank, sliding in an upward motion.
NOTE:
Hose must be removed before inlet deflector can be taken out.
For dry pick up be sure the opening of the inlet deflector is facing the tank bottom
(Figure 18)
. If the vacuum has been used to pick up liquids, the
foam sleeve must be cleaned and dried before installing for dry pick up. With tank cover in an upside down position, slide foam sleeve down over
lid cage pulling until foam sleeve completely covers lid cage
(Figure 19, 20).
Center the reusable dry filter on lid cage
(Figure 21)
, slide
mounting ring down over filter until ring is positioned against the ribs of the lid cage
(Figure 22)
. The reusable dry filter should always be in
position over the foam sleeve for dry pick up. To remove the filter for cleaning, remove mounting ring and filter from lid cage
(Figure 23)
. To
clean the reusable dry filter, shake off excess dirt and dust or (depending on the condition of the filter) rinse with water. Allow the filter to dry
completely and reinstall. DO NOT MACHINE WASH OR DRY.
18
19
20
NOTE:
Ensure that the mounting ring is completely secure and in position by pressing down firmly around the ring in several places. Be sure the
reusable dry disc filter completely covers the foam sleeve. Check to ensure that all edges of the reusable dry filter are secure under the mounting
ring.
CAUTION-
KEEP FILTERS CLEAN
A
Arrow
A
10
12
11
9
B
B
A
A
Template
Bottom of Tank
7
8
Tank Bottom
13
14
16
15
4
6
5
3
2
1
21
22
23
