NOTE: ENSURE THAT THE MOUNTING RING IS COMPLETELY SECURE AND IN POSITION BY PRESSING DOWN FIRMLY AROUND THE RING IN SEVERAL
PLACES. BE SURE THE REUSABLE DRY DISC FILTER COMPLETELY COVERS THE FOAM SLEEVE. CHECK TO ENSURE THAT ALL EDGES OF THE
REUSABLE DRY FILTER ARE SECURE UNDER THE MOUNTING RING.
CAUTION -
KEEP FILTER CLEAN.
Efficiency of the vacuum is largely dependent on the filters. Dirty filters will reduce the air flow and efficiency of the filtration system.
DO NOT MACHINE WASH OR DRY.
WET PICK UP OPERATION
When vacuuming fine dust or powders of any kind - (eg) plaster, drywall
dust, cold ashes, concrete dust, etc. . . a disposable collector filter bag
must be used. These "large bag" filters connect to the air inlet fitting on the
inside of the vacuum tank.
1. Grasp cardboard collar firmly and slide rubber guard onto inlet fitting as
far as possible.
2. When secured in place, expand bag and position around side of tank.
USE FOR DRY PICK UP ONLY
CORRECT DISPOSABLE FILTER INSTALLATION
Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of conversion when going from dry to wet pick up. Wet pick
up requires the foam sleeve
(not standard on all models)
to be in position over the lid cage. Do not use the reusable dry filter
(not standard on
all models)
for wet pick up. Misting in exhaust air may occur if the foam sleeve becomes saturated during wet pick up. If misting occurs, remove
and dry the saturated foam sleeve or replace with another dry foam sleeve to eliminate the misting and possible dripping of liquid around the lid.
Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be emptied. Raise the hose to drain any excess
liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place tank cover in an upside down position. Remove
foam sleeve by sliding it up and off the lid cage.
2. Shake excess dust off foam sleeve with a rapid up and down movement.
3. Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water wash is not always required, depending on the
condition of the foam sleeve.
4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The foam sleeve is now ready to be reinstalled on the lid
cage.
NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS
CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER.
INSTALLING THE CARTRIDGE FILTER •
NOT STANDARD ON ALL MODELS
WARNING -
ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING
THE TANK COVER.
1. Slide cartridge filter down over lid cage.
2. Place filter retainer on top of cartridge filter. Hold onto base of lid
cage with one hand and turn retainer clockwise to tighten.
3. To remove filter for cleaning, again hold onto base of lid cage with
one hand and turn retainer counter clockwise to loosen.
4. Slide cartridge filter off lid cage.
TIGHTEN
LOOSEN
INSTALLING THE DISPOSABLE FILTER BAG
•
NOT STANDARD ON ALL MODELS
EMPTYING LIQUID WASTE FROM THE TANK
Use special care when emptying heavily loaded tanks. Your Wet/Dry Vacuum may be emptied of waste by removing the tank cover. To empty, stop
the motor and remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste contents into a suitable drain. Your
Wet/Dry Vac also comes with a convenient tank drain
(not standard on all models)
. Simply remove the drain cap and empty the liquid contents
into a suitable drain. After the tank is empty, return the cover to its original position. To continue use, plug the cord into the wall receptacle and start
the motor.
