background image

Warranty

Woodstock International, Inc. warrants all 

SHOP FOX

®

 machinery to be free of defects from work-

manship and materials for a period of two years from the date of original purchase by the original 

owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence 

or accidents, lack of maintenance, or reimbursement of third party expenses incurred. 

Woodstock International, Inc. will repair or replace, at its expense and at its option, the 

SHOP FOX

®

 

machine or machine part which in normal use has proven to be defective, provided that the original 

owner returns the product prepaid to the 

SHOP FOX

®

 factory service center or authorized repair 

facility designated by our Bellingham, WA office, with proof of their purchase of the product within 

two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged 

defect through inspection. If it is determined there is no defect, or that the defect resulted from 

causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must 

bear the cost of storing and returning the product. 

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be 

implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited 

to the duration of this written warranty. We do not warrant that 

SHOP FOX

®

 machinery complies 

with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under 

this warranty exceed the purchase price paid for the product, and any legal actions brought against 

Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall 

in no event be liable for death, injuries to persons or property or for incidental, contingent, special or 

consequential damages arising from the use of our products. 

Every effort has been made to ensure that all 

SHOP FOX

®

 machinery meets high quality and durabil-

ity standards. We reserve the right to change specifications at any time because of our commitment to 

continuously improve the quality of our products.

Содержание SHOP FOX M1104





























Отзывы: