WARRANTY
Warranty Support and Service for Shocker Paintball (SP) products is provided by factory trained service technicians at
SP Authorized Dealers.
SP warrants for one (1) year to initial retail purchaser that the Paintball Marker and Regulator components are free from defects in
materials and workmanship. The Valve Assembly and Solenoid are warranted for six (6) months. Disposable parts (Batteries,
O-Rings, Seals, etc.) are not warranted.
This warranty does not cover surface damages (scratches and nicks), misuse, improper disassembly and reassembly, attempts made
to drill holes or remove metal from external surfaces which could degrade the performance and reduce pressure safety factors of the
marker without written approval. Re-anodizing of any part of the marker voids any warranty claim. The only authorized lubricant for the
marker is GR33SE™ Lubricant. Use of any other lubricant could result in voiding your warranty. Paintball Markers are non-refundable.
This warranty is limited to repair or replacement of defective parts with the customer responsible for transporting the product to
and from the Shocker® XLS Authorized Dealer. Modification of any kind to the trigger assembly may result in serious injury, any
modifications made to this system void all warranty obligations.This warranty is effective only if the customer registers their
marker online at www.shockerpaintball.com/support in our RMA system within 30 days of original purchase.
The warranty is non-transferable.
FIG. 2
Shocker® and Freak® are registered trademarks owned by G.I. Sportz Inc. and used under license by Philadelphia Americans, LLC.
QUICK START
GUIDE
[v1.0]
BOLT MAINTENANCE
MARKER SETUP
WARRANTY
WARNING
THIS IS NOT A TOY. MISUSE OF THE SHOCKER XLS MAY RESULT IN SERIOUS INJURY OR DEATH. EYE PROTECTION
DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE OF THE SHOCKER® XLS.
SHOCKER PAINTBALL (SP) RECOMMENDS THAT THE SHOCKER ® XLS ONLY BE SOLD TO PERSONS 18 AND OLDER.
THOROUGHLY READ THE SHOCKER® XLS QUICK START GUIDE BEFORE OPERATING.
WWW.
SHOCKER
PAINTBALL.COM
SHK
208
SHK
256
SHK
110
SHK
304
SHK
123
CLP
003
SHK
103
SPR
016
SHK
205
BUM
004
POWER
PROGRAMMING
LOCK
MODE & BPS CAP
PROGRAMMING
LOCK
VISION STATUS
LIVE ROF
SOFTWARE
VERSION
BATTERY
LEVEL
01
BATTERY
02
POWER
06
BOLT DISASSEMBLY
VALVE AND BOLT DISASSEMBLY/ MAINTENANCE
When cleaning or maintenance is necessary, unload and degas the marker. If the
valve release button is pressed while the Shocker® XLS is still pressurized the bolt system will eject approximately 1/2 inch and degas safely.
*NOTE*– It is strongly recommended that the Shocker® XLS be degassed before pressing the valve release button. Pressing the valve
release button while the marker is pressurized will un-seat the front most o-ring on the main chamber [SHK208] [FIG. 06]. Simply
reinstall this o-ring prior to reassembly. To access the bolt system, press the valve release button at the rear of the body. Pull the valve
assembly out of the body by its tail cover.
Unscrew the main chamber [SHK304] from the firing can [SHK208] and remove the bolt. Remove the chamber guide [SHK110] from
the main firing chamber as well.
Clean all parts and the interior of the body with a soft cloth and inspect all O-rings for tears or other damage – replace if necessary.
Lightly lubricate all O-rings with GR33SE™ marker lubricant (DO NOT USE OIL) and reassemble in reverse order.
Take care not to cross-thread the bolt pieces while re-assembling. Gently slide the valve assembly into the Shocker® XLS and press
in on the Tail Cover until it latches in place. If the latch does not engage; check for debris in the latch and confirm the bolt system is
correctly assembled and its components snuggly tightened.
BATTERY
A 9-volt battery powers the electronic components in the Shocker
XLS. For optimal performance, alkaline batteries (ANSI type 1604A) should be
used. Lower cost “heavy duty” zinc/carbon batteries should be avoided. Most 9v
rechargeable batteries will work with the Shocker® XLS, however their charge
levels may display inaccurately due to amperage limitations of the battery.
To install or replace the battery in the Shocker® XLS, place the marker on a flat
surface with the feed tube on your left hand side. Remove the three grip screws
using a 5/64-inch allen wrench. Grasp the battery lead wires and connector,
and snap the connector onto the battery. Wrap the battery lead wires around
the connector once, this will secure the wires and prevent them from being
pinched when placing the battery into the frame. The battery should be installed
with the connector pointing toward the top of the grip frame.
[FIG. 01]
Because the Shocker® XLS circuit board draws a very small amount of current
from the battery even when it is turned off, it is best to remove the battery if the
marker is going to be stored for a few weeks or more.
POWER BUTTON
Turn on the Shocker® XLS by pressing and holding the power
button for a full second. As soon as the Shocker® XLS is on, it is live and ready
to fire. Press and hold the power button to turn off the Shocker® XLS. [FIG. 02]
VISION ON/OFF
Vision mode is active by default upon start up of the Shocker®
XLS. The power button flashing or glowing green will indicate that vision mode
is active, and an open or filled circle under “EYE” will be indicated on the OLED
screen. To disengage vision mode, press the power button for one second, the
power button will flash red and the OLED screen will indicate “OFF” in the vision
section.
PROGRAMMING LOCK
The Shocker® XLS is equipped with a programming
lock feature. When the Shocker® XLS is locked, the electronic settings that
impact firing modes, rate of fire and velocity may not be changed. Because the
lock button cannot be accessed without tools, the Shocker XLS complies with all
major tournament and scenario rules as well as common paintball field practices.
The OLED screen will display the programming lock status. A padlock symbol
appears closed while the marker is locked, and appears open while it is unlocked.
To lock or unlock the Shocker® XLS, access the board through the grips (see
Battery Installation). With the marker turned on, momentarily press the lock
button [FIG. 01] to toggle locked or unlocked status.
