background image

LOG SET PLACEMENT IN FIREPLACE

XXXX

XXXX

XXXX

XX

Glowing Embers

 to the

area marked with 

“XXX” (see Figure 6

).

Do not apply 

Glowing Embers

 to the main burner.

Figure 6- Glowing Ember Placement

INSTALLATION 

(Continued)

DECORATIVE CRUSHED SHALE

Included with this Gas Log Set is a bag of Crushed 

This Shale is provided to enhance the look and feel 

of your log set and fireplace. Its only function is to 

be decorative. Simply spread the Crushed Shale on 

your fireplace floor around the bottom of your log 

set burner/grate to give the appearance of burnt 

ash. It can also be used to cover your gas supply    

Caution: Never place the shale, or any other object 

(not provided with your gas log set and instructed 

for that purpose) onto the burners of the unit. 

Be creative in the placement. You do not have to 

use all of the supplied shale.   

CRUSHED SHALE SHOWN 

AS PROVIDED

line coming from the wall to your burner.

Shale (

see Figure 7

)

Figure 7- Crushed Shale

11

OPTIONAL ON/OFF 

REMOTE CONTROL SET

INSTALLATION AND OPERATION

- + - +

COMMUNICATION BETWEEN THE

REMOTE CONTROL TRANSMITTER

AND THE RECEIVER

To program the transmitter to the receiver

,

move

the three positions slider of the receiver inthe

REMOTE

position and depress the

ON/OFF

key

of the transmitter. The System has an automatic

learning mode that allows the receiver to mate

with a new trans

-

mitter in the event the trans

mitter must be replaced. Assoon as the receiver

module receives the firstcorrectcommand from

any remote control it captures the new address

and then "beeps"3 times to confirm the syncron-

ization and command execution..

Remote control set NOT included with log set. If 

using the optional remote control set, follow these 

additional instructions. 

Install four

(

4) "AA"

batteries into the

remote receiver box

as shown on the left.

Install three

(

3) "AAA"

batteries into the

remotecontrol

as shown on the left.

Be sure to place the remotereceiver in a cool loc-

ation in the fireplace. Do not place the reciever

in a location directly in front of the burner system.

Содержание GRVFE24LMV

























Отзывы: