Shindaiwa DGW400DM-380A Скачать руководство пользователя | Manualshive

Страница: 8 / 38

background image

5. Equipment

5-1 Eco Welding

The equipment is incorporated in Eco welding features that are aimed at performing
the lower noise, the lower fuel consumption and the lower gas emission than
conventional models.
When you turn the selector switch to Eco, you will be able to weld with Max.
5.0mm

φ

welding rod at the slow down speed.

<Caution>

z

When welding is performed, do not turn the output selector switch, which causes

the burnout of the switch.

z

Eco is designed for welding only. The 3-phase circuit breaker trips and

simultaneously the outputs of welding and generating would fall down and you will
not do anything when Eco is used for AC power supply.

5-2 Remote Control (Option)

Using the remote control box, the remote control to adjust the welding current
makes it possible.

Remote Control Box Connection

Remove “Eco” plate. (M4 Screw 2 pieces)

Insert the plug of the extension cable reel

into A side or B side receptacle

Insert the plug of the remote control box

into the receptacle of the extension cable
reel.

<Caution>

z

Never connect the plug of the remote control box to the receptacle of the

extension cable reel when the reel is connected to 1-P receptacle.

z

Never connect the other loads additionally than the remote control box.

z

In the case the extension cable reel is installing the breaker, use the equipment to

have turned the breaker ON.

- 7 -

«
...
6
7
8
9
10
...
»

Содержание DGW400DM-380A







































Отзывы:

Нет отзывов

Похожие инструкции для DGW400DM-380A

Бренд: 1byone Страницы: 17

Бренд: 2N Страницы: 23

Бренд: Eagle Equipment Страницы: 32

Бренд: Omni Страницы: 108

JBL BAR 5.0 MULTIBEAM

Бренд: Harman Страницы: 25

Бренд: Parkside Страницы: 54

Бренд: Teac Страницы: 24

Бренд: Teac Страницы: 24

Бренд: TeachLogic Страницы: 21

Бренд: VENCO Страницы: 44

Бренд: Wabtec Страницы: 106

Бренд: salmson Страницы: 16

Бренд: Sabiana Страницы: 56

DTS-212 SPEAKER SYSTEM

Бренд: Altec Lansing Страницы: 8

Бренд: Rotary Страницы: 16

Бренд: Pix Controller Страницы: 21

Бренд: Zuden Страницы: 19

SpeedFace Series

Бренд: ZKTeco Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды