Shindaiwa C230 INTL Скачать руководство пользователя страница 9

Страница: 9 / 24

Assembly

Ground Wire

Terminal

Ground

Wire

Assemble and Adjust
the Throttle Cable.

1. Insert the throttle-cable housing into the

notch on the fan cover, and clamp the
ground wire teminal between the fan
cover and the outer cable adjuster nut.
See Figure 13.

2. Tighten the two throttle cable adjuster

nuts.

IMPORTANT!

Adjust and tighten the cable nuts to allow
approximately 1/4-inch freeplay at the
throttle trigger.

3. Using

nger pressure only, connect the

black ignition wire from the cable tube
to the red ignition wire on the power-
head. Wire routing must be as shown
in the illustration with the black wire
located away from the throttle cable
and carburetor linkage.

CAUTION!

Routing of wiring must not interfere with
throttle operation.

Figure 13

Reinstall the Spark

Plug Cap

Black Ignition

Wire

Red Wire

Cable Adjuster

Nuts

23013

Assembly

Throttle Linkage and Ignition Leads

Remove the Cylinder Cover.

1. Remove the cap from the spark plug.
2. Loosen the black cylinder cover knob

(about a dozen full turns are required),
and then lift off the cylinder cover.

NOTE:

If the cover binds on the muffl er outlet
tube, pull gently on the corner of the cover
as shown (see inset).

Connect the Throttle Cable.

1. Route the ribbed cable over the tube

clamp to the top left side of the engine.

2. Install the black wire between the two

cable adjuster nuts as shown.
See Figure 11.

3. Connect the S-shaped end of the

throttle cable to the throttle lever on top
of the carburetor. See Figure 12.

Install the black wire

between the two cable

adjuster nuts.

Connect the

throttle cable

Ignition

Ground

Lead

Cable Adjuster

Nut

Figure 11

Figure 12

23014

Loosen the

cylinder cover

knob and

disconnect the
spark plug cap

Lift the corner of

the cover

Figure 10

4. Reinstall the engine cover and tighten

the captive engine cover screw.

5. Reinstall the spark plug boot.

Содержание C230 INTL

























Результаты поиска

Содержание C230 INTL

Отзывы:

Похожие инструкции для C230 INTL

Бренды по названию

Популярные бренды

Shindaiwa C230 INTL, Руководство владельца/оператора

Результаты поиска

Содержание C230 INTL

Отзывы:

Похожие инструкции для C230 INTL

Бренды по названию

Популярные бренды