Shindaiwa 80465 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 24

background image

20

Troubleshooting Guide

ADDITIONAL PROBLEMS

Symptom

Possible Cause

Remedy

Excessive
vibration.

Warped or damaged
tines.

Loose gearcase.

Bent main shaft/worn or
damaged bushings.

Inspect and replace
tines as required.

Tighten gearcase securely.

Inspect and replace
as necessary.

Tines will not
rotate.

Tines rotate at
engine idle.

Shaft not installed
in coupler or
gearcase.

Broken shaft.

Damaged gearcase.

Engine idle too high.

Broken clutch spring
or worn clutch spring
boss.

Inspect and reinstall
as required.

Consult with an authorized
servicing dealer.

Consult with an authorized
servicing dealer.

Adjust engine idle speed
2,750 RPM. (

Ⳳ

250 ) RPM (min

-1

)

Replace clutch spring
and shoes as required.

TROUBLESHOOTING

«
...
18
19
20
21
22
...
»

Содержание 80465

























Отзывы:

Нет отзывов

Похожие инструкции для 80465

Бренд: Simplicity Страницы: 20

Бренд: Yard-Man Страницы: 20

AP20BCF200-3-XL

Бренд: American Panel Страницы: 36

Бренд: Gree Страницы: 58

Бренд: AERMEC Страницы: 72

Бренд: Nemco Страницы: 2

Бренд: Cavecool Страницы: 27

Бренд: Ruris Страницы: 42

Бренд: AIREDALE Страницы: 302

Бренд: Toyama Страницы: 60

RAPID RDA S Series

Бренд: Vaderstad Страницы: 122

Бренд: Troy-Bilt Страницы: 40

Series 200 World Rear Wheel Tiller

Бренд: Troy-Bilt Страницы: 68

Бренд: Cub Cadet Страницы: 15

Бренд: Cub Cadet Страницы: 20

Бренд: Daikin Страницы: 156

Бренд: EarthQuake Страницы: 32

ZANUSSI Easychill 110044

Бренд: Zanussi Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды