Shindaiwa 63848-94010 Скачать руководство пользователя страница 5

Safety Equipment and Labels

Shaft Safety Label

Figure 1

Throttle Interlock

Ignition

Switch

High Voltage Label

Cutter Blade

Scabbard

Hand

Guard

4

IMPORTANT!

Safety and Operation Information
Labels: Make sure all information
labels are undamaged and readable.
Immediately replace damaged or
missing information labels. New labels
are available from your local autho-
rized Shindaiwa dealer.

SAFETY

Your Warranty Rights and
Obligations

The California Air Resources Board, the
U.S. Environmental Protection Agency
and Shindaiwa Kogyo Co., Ltd. are
pleased to explain the emission control
system warranty on your new small off-
road (non-road) engine.

In California, new small off-road

engines must be designed, built, and
equipped to meet the State’s stringent
anti-smog standards. In other states,
new 1997 and later non-road engines
must meet the Federal EPA’s strin-
gent anti-smog standards. Shindaiwa
Kogyo Co., Ltd. must warrant the
emission control system on your small
off-road engine for the periods of time
listed below, provided there has been
no abuse, neglect, or improper
maintenance of your small off-road
engine.

Your engine emission control

system includes parts such as the
carburetor, the ignition system and, if
equipped, the catalytic converter.
These components are specifically
listed below.

Where a warrantable condition

exists, Shindaiwa Kogyo Co., Ltd. will
repair your small off-road engine at no
cost to you including diagnosis, parts,
and labor.

Manufacturer’s Warranty
Coverage

When sold within the U.S., this

engine’s emission control system is
warranted for a period of two (2) years
from the date this product is first
delivered to the original retail pur-
chaser.

During the warranty period,

Shindaiwa Kogyo Co., Ltd. will, at
their option, repair or replace any
defective emission-related component
on this engine. During the original
Warranty Period, these Warranty
Rights are automatically transferable
to subsequent owners of this product.

What is Covered by this
Warranty

1. Carburetor Internal Components

 Throttle Valve, Needle, Jet,

Metering Diaphragm

2. Ignition System Components

 Ignition Coil

 Flywheel Rotor

3. Catalytic Converter (if originally
equipped)

The emission control system for

your particular Shindaiwa engine may
also include certain related hoses and
connectors.

Emission System Warranty Statement

31

Содержание 63848-94010



















Отзывы: