Set to
➃
➃
0
2
S
8 - J
C
N
A
P
A
J
K C
O L
CJ-8S20
JAPAN
KC
OL
CJ-8S20
JAPA
N
K C O L
CJ-8S20
JAPAN
KC
OL
10 cm
10 cm
15 cm
CJ-8S20
JAPAN
KC
OL
CJ-8S20
JAPAN
KC
OL
CJ-8S20
JAPAN
KC
OL
0
2
S
8
-
J
C
N
A
P
A
J
0
2
S
8
-
J
C
N
A
P
A
J
K
C
O
L
CJ-8S20
JAPAN
KC
OL
CJ-8S20
JAPAN
KC
OL
If the yellow setting lines are not aligned,
turn the cable adjustment bolt of the
Revoshift lever to align the setting lines.
After this, move the Revo-shift lever once
more from
➃
➃
to
➀
➀
and then back to
➃
➃
,
and then recheck to be sure that the yellow
setting lines are aligned.
Inner cable fixing bolt unit
Note: Do not use this inner cable fixing bolt
unit with the CJ-4S30 cassette joint.
9
5.
Pass the inner cable through the
SIS-SP40 outer casing through the
end with the plastic cap.
6.
After checking that the end of the
outer casing is sitting securely in
the cable adjustment bolt of the
Revo-shift lever, attach the inner
cable fixing bolt unit to the inner
cable.
7.
Bring the cable around to the
cassette joint pulley, hold so that
the inner cable fixing nut is facing
to the outside (toward the fork
end), and then slide the flats part
of the inner cable fixing washer
into the gap in the pulley.
■
Cassette joint side
Plastic cap
Attach the plastic cap.
Remove the plastic cap.
Aluminium cap
Inner cable fixing
nut
Inner cable fixing
washer
Inner cable fixing
bolt
Inner cable
fixing nut
Pulley
If cutting the outer casing, cut it near the
end with the plastic cap while the cap is
still attached. Then make the cut end
perfectly round and attach the plastic cap.
Plastic cap
10 mm
(Black)
Pass the inner cable
through the hole.
101 mm
Pull the inner cable while attaching the inner
cable fixing bolt unit.
Tightening torque:
4 – 6 N·m {40 – 60 kgf·cm}
Flats part of inner
cable fixing washer
Gap in pulley
10.
Secure the cable to the frame with
the outer casing bands.
8.
Turn the cable 60º counterclockwise
and attach it to the hook.
9.
Attach the inner cable to the pulley
as shown in the illustration, pass the
inner cable through the slit in the
cassette joint bracket, and then
insert the end of the outer casing
securely into the outer casing holder.
Hook
Turn the
cable 60º
Bracket
Inner cable
Pulley
Bracket
Slit
Outer casing holder
Pass through the slit
2
1
Insert into
the outer
casing
holder
Make the cut end
perfectly round.
If first inserting the outer casing into the
outer casing holder is easier, then first insert
the outer casing into the outer casing hold-
er, and then insert a 2 mm Allen key or a
#14 spoke into the hole in the cassette joint
pulley, and then turn the pulley so that the
inner cable fixing bolt unit fits into the gap
in the pulley.
Note:
Check that the inner cable is correctly seated
inside the pulley guide.
2 mm Allen key or #14 spoke
Insert the inner
cable fixing bolt
unit.
Turn the
pulley
Insert into the
outer casing
holder.
Hole in pulley
2
3
1
Outer casing bands
OK
Not OK
Guide
Guide
2.
After adjusting the cassette joint, cut
off the excess length of inner cable
and then install the inner end cap.
Cable adjustment bolt
1.
Set the Revo-shift lever to
➃
➃
.
Check to be sure that the yellow setting
lines on the cassette joint bracket and
pulley are aligned at this time.
Adjusting the cassette joint
Inner end cap
Yellow setting lines
The yellow setting lines on the cassette joint
are located in two places. Use the one that
is easiest to see.
When bicycle is standing up
When bicycle is upside down
Cassette joint
bracket
Cassette joint
bracket
Cassette
joint pulley
Should be straight
Cassette
joint pulley
15 – 20 mm
Should be straight
Lay_INTER-8_GB 05 23.12.qxd 23.12.2004 13:39 Uhr Seite 9
