No. 2
Cable
Color and Signal
Connector
GAT10-DN
■
DeviceNet Specifications
Transmission rate
125k bps
250k bps
500k bps
Setting not allowed
●
DeviceNet transmission rate setup
■
RS-485 (Shimaden standard protocol) Specifications
Specifications
EIA RS-485 compliant
2-line half duplex multidrop
Start-stop synchronization
Max. 500 m
19200 bps
7 bit/even parity/1 stop bit
Max. 8
SR80 series, SR90 series, SR253, SD16, EM70, FP93
Approx. 1.5 sec
(when 8 Shimaden units are connected and without SV
value updating, and parameter reading/writing)
Terminal arrangement
●
Use the special cable for DeviceNet.
●
Use the attached connector.
●
The connector is equivalent to the MTB2, 5/5-ST-5. 08 ABGYAU made by PHOENIX CONTACT.
●
For grounding and terminating resistor for DeviceNet, refer to the DeviceNet Specifications published by
ODVA.
4. Wiring
■
Connecting DeviceNet communications
Item
Signal level
Communication method
Synchronization method
Communication distance
Communication rate
Data format
Number of connectable
Shimaden instrument
Connectable products
Scan time
■
Connecting RS-485 communications
RS-485
Power supply
Terminating resistor
(attached to the instrument)
Shimaden instruments
No particular maintenance is required for the GAT10-DN. Check the inspection items listed in Master
PLC User's Manual so that your system can always be used in optimal conditions.
■
Maintenance
●
The external line should not be bundled with or installed adjacently to a load line except tho se from
the main power circuit line, a high voltage line and the PLC. Otherwise it will easily be affected by
noise, surge or induction.
●
For a shielding wire or a shielded cable, one-point grounding on the PLC side is required. Depending
on the condition of external noise, however, it may be better to ground on the externa l side.
1 to 8
Local address
Connector
Network current consumption
Special cable for DeviceNet
125k bps
500k bps
250k bps
500 m
100 m
250 m
Specifications
Master/slave system
CAN Protocol
Trunk line, Drop line
125k/250k/500k bps
Fixed to 24 words each for input and output
0
～
63
Communication adaptor
Accessories
40mA max.
Item
Communication system
Protocol
Type of transmission line
Type of device
Occupied word count
Node address
Maximum transmission
distance
Connecting cable
Transmission rate
SW6
OFF
ON
OFF
ON
SW7
OFF
OFF
ON
ON
●
DeviceNet Node Address Setup
NA0
Address
0
1
・・・
62
63
NA5
NA4
NA3
NA2
NA1
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
・・
・・
・・
・・
・・
・・
ON
ON
ON
ON
ON
ON
2
ON
ON
OFF
OFF
OFF
OFF
■
External Wiring
As one of the requirements for enabling the GAT10-DN to function thoroughly and to establish a
highly reliable system, external wiring that is not easily affected by noise is necessary. The following
are matters to be attended to for external wiring.
Signal
V-
CAN_L
Drain
CAN_H
V +
Color
Black
Blue
----
White
Red
The GAT10-DN has a built-in RS-485 terminating resistor. To the Shimaden instrument as the final
station, attach the terminating resistor supplied as an accessory to it. However, please attach the
terminating resistor to only one instrument (final station). If attached to two or more i nstruments,
correct operation cannot be guaranteed.
Note: No devices except Shimaden instruments should be connected to the RS-485 line. Otherwise,
correct operation cannot be guaranteed.
Note: Make sure to use GAT10-DN as a terminal station of RS-485 communications.
■
Terminating resistor
●
DeviceNet
●
RS-485
Install the DeviceNet terminating resistor according to the Master PLC Instruction Manual and the
DeviceNet Specifications issued by ODVA.
Transmission rate
Total length
GAT10-DN
SHIMADEN
POWER
RESET
MS
NS
RX
TX
LED indicating operating status of DeviceNet
LED indicating operating status of RS-485
communication
Reset switch
Switch for transmission rate setup
( SW6, SW7 )
Note: Set values become effective upon applying
power
or resetting.
DeviceNet
connector
V-
CAN_L
CAN_H
Drain
V+
Switch for node address setup
( NA0
～
NA5 )
Lights "green" when GAT10-DN
operates normally. In other displays,
setting error/device error has occurred.
Name
Color
Function
Remarks
ＭＳ
Green/
Red
Module status
(DeviceNet)
Lights "green" when GAT10-DN is on-
line. In other displays, communication
failure/connection error has occurred.
ＮＳ
Green/
Red
Network status
(Device Net)
Lights during reception of data
ＴＸ
Green
RS-485
Data transmission
Lights during transmission of data
ＲＸ
Green
RS-485
Data receipt
●
LED indicating operating status
V -
CAN_L
Drain
CAN_H
V +
V -
CAN_L
Drain
CAN_H
V +
Name of Signal
No.
①
②
③
④
⑤
⑥
⑦
⑧
RS-485
: -
RS-485
: +
NC
Power supply: N
Power supply: L
Power supply: FG
RS-485
: SG
NC
L
N
⑤
⑥
⑦ ⑧
④ ③
②
①
・
・
・
No. 1
+
-
SG
+
-
SG
No. N
(the final station)
+
-
SG
The contents of this manual are subject to change without notice.
Temperature and Humidity Control Specialists
Head Office: 2-30-10 Kitamachi, Nerima-Ku, Tokyo 179-0081 Japan
Phone: +81-3-3931-7891 Fax: +81-3-3931-3089
E-MAIL: [email protected] URL: http://www.shimaden.co.jp
PRINTED IN JAPAN
