Shihlin electric SPM-3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

Shihlin electric SPM-3 Скачать руководство пользователя страница 13

_________________________Shihlin Electric SPM-3 User Guide__________________

12

N7: CT Primary Setting from 1-5000 (Default 1)

N7
CT1

0001

N8: CT Secondary Setting from 1-5 (Default 1)

N8
CT2

1

N9: BACK LIGHT TIME OUT Setting from 0-120 minutes (Default 1) .

If 0 is chosen, the back light will always be ON. Press any key to turn on back light.

N9
BACK
LIT

120

N10: BACK LIGHT LEVEL Setting from 0-4 (Default 3).

If 0 is chosen, the back light will always be OFF.

N10
BACK
LIT
LVL

3

N11: I-1 Current Direction Setting - “Positive” or “Negative”. (Default POSITIVE).

If the current is connected in wrong direction, select “Negative” to correct the display

value.

N11
I-1

POSITIV E

N12: I-2 Current Direction setting - “Positive” or “Negative”. (Default POSITIVE).

If the current is connected in wrong direction, select “Negative” to correct the display

value.

N12
I-2

POSITIVE

N13: I-3 Current Direction setting - “Positive” or “Negative”. (Default POSITIVE).

If the current is connected in wrong direction, select “Negative” to correct the display
value.

N13
I-3

POSITIVE

N14: V1(V12) Voltage Eligibility Rate Upper Limit Setting from 0-65535 (Scale 0.1, refer to

Secondary) (Default 65535)

N14
U1
UP
LMT

65535

N15: V1(V12) Voltage Eligibility Rate Lower Limit Setting from 0-65535 (Scale 0.1, refer to

Secondary) (Default 0)

N15
U1
LOW
LMT

00000

«
...
11
12
13
14
15
...
»

Содержание SPM-3





































Отзывы:

Нет отзывов