SEAT DESIGNS MAY
VARY BUT THE ASSEMBLY
IS THE SAME
NOTE: MAKE SURE ARROWS ON
BOTH THE "U" BAR AND
SWIVEL BASE ASSEMBLY
ARE POINTING IN THE
SAME DIRECTION.
Step 1:
Do not attempt
to assemble the chair if any parts re damaged or missing.
IMPORTANT NOTE: WE RECOMMEND TWO PEOPLE WORK TOGETHER
TO ASSEMBLE THE CHAIR.
Step 2:
Step 3:
Step 4:
Step 5:
Do not
over tighten.
Step 6:
Identify all parts packed in carton against the parts list. Remove all protective
materials. Place parts on a non-abrasive surface to avoid scratching. If you
are missing any parts or are unsure how to proceed with assembly, please call
our Customer Service Center immediately at 1-800-416-3511.
Position the swivel base on a flat, solid surface. Make sure the swivel plate is
positioned all the way into the base. It may have vibrated out during shipment.
The two sets of holes in the swivel plate should be facing away from you.
Note the arrows on both the swivel plate and the "U" bar portion of the chair
frame. Position the chair frame onto the swivel plate so that the two pairs of
holes in the "U" bar are exactly aligned with the two pairs of holes in the
swivel plate and the arrows on both the "U" bar and swivel plate are pointing
in the same direction. Proper positioning of the chair frame on the swivel
plate/swivel base assembly, and proper alignment of the holes in the "U" bar
with the holes in the swivel plate are critical to the safe, well balanced
swiveling motion of the chair.
Carefully examine the diagram. Attach a metal plate to four (4) bolts and
guide the bolts through the top of one set of holes in the "U" bar (located
under the chair frame) and into the pair of holes in the swivel plate. From
beneath the swivel plate, add a washer, then a spring washer, then a nut to
the end each bolt. Hand tighten 3-4 revolutions only. Repeat procedure for
the pair of holes on the opposite side. Again, hand tighten nuts 3-4
revolutions only. Do not tighten nuts completely.
At this time tighten all nuts and bolts with the hex wrenches provided.
Over tightening may strip the bolts and cause damage to the
swivel plate, making the chair unsafe. Cover bolts with bolt covers.
Your chair should now be ready for use. If you do not feel that your chair is
swivelling properly, double-check your assembly procedure, especially step 4.
If you have any questions, please call our Customer Service Center at
1-800-416-3511
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened
bolts or improper assembly is not covered under our warranty. Please read
all instructions carefully before assembly. If you have any questions regarding
your assembly, call our Customer Service Center at 1-800-416-3511.
Page 2
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
SWIVEL PLATE
ADV07511
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
FOOT CAP
HW0686
G
C
D
F
E
H
SLING TUBE CAP
FACTORY ASSEMBLY
SWIVEL BASE
FOOTREST COVER
FACTORY ASSEMBLY
G0155
FOOT CAP
FACTORY ASSEMBLY
HEX WRENCH-1
HW0008
1
HEX WRENCH-2
HW0007
1
QTY
PARTS LIST
DESCRIPTION
ORDER PART #
BOLT COVER
HW0028
4
QTY
5/16" X 43 MM
BOLT
Ø
8.0 X 2.3 MM
SPRING WASHER
HW0003
5/16" NUT
HW0015
METAL PLATE
CHAIR FRAME
PARTS LIST
DESCRIPTION
ORDER PART #
2
4
4
4
1
1
HW0450
A
B
C
D
E
F
G
H
4
Ø8 5 X 1 5 MM
WASHER
.
.
HW0005
FC0082
FC0831
A
B
AS0075
AS0076
