background image

b. Use a clean, dry cloth to wipe the piston surface if it needs cleaning.

c. Do not put the piston in a cleaning solution or ultrasonic cleaner. If there is any oil on 

the surface, it will coat the piston. 

d. A coating of grease or oil will interfere with the air flow through the flow control element in the 

face of the piston (see Photo #5). It may also cause the Dry Air Bleed System to cease 
working. Although this is not dangerous to the diver, it may increase the difficulty of breathing 
through the regulator upon descent. 

e. If no air is bubbling from the one-way bleed valve, this is a good indication that the positive air

purge system is not working. 

13.

Place a new piston seat on a clean piece of paper, on a hard, flat surface. Press the piston tip
firmly over the seat until it is fully installed. The piston is now rebuilt, and ready for installation.

14.

Use a pocket screwdriver to remove the star washer      that holds the filter      in place. Most
units used a star washer (a flat disc washer with six outward facing legs). Units made after 1997
use a wire-retaining ring with a forward hook. The only first stage bodies that can use this re-
useable ring, have a groove machined into the area above the filter for the ring to fit snugly into.
Always discard the used filter and old style star washers, newer style retaining rings are saved 
for reuse.

15.

Remove the moving orifice      from the body by pushing it with a soft plastic probe from the
large threaded end of the body. Catch the orifice assembly in your hand as it comes out the
yoke nut thread end of the body (see Photo # 6). Carefully inspect the disc springs      for any
cracks. Replace all five disc springs if any cracks are found.

8

Photo #5

Photo #6

2

3

4

5

Содержание Scuba MAXIMUS SRB3600 regulator






























Отзывы: