background image

 

Important! 

The tiller blades will continue to rotate for a few  seconds after the motor is switched off. Never 

attempt to manually stop them. In the event that the rotating tiller blade strikes an object, 

immediately switch off the machine and wait for the tiller blades to come to a complete stop. Then 

inspect the condition of the tiller blades. Replace any parts that are damaged. 

Lay the power cable on the ground in front of the outlet in a figure 8. Work away from the outlet or 

cable and ensure that the power cable always trails in the tilled soil which will prevent the tiller 

blades from traveling over the cable. 

 

 

6.  Replacing the power  cable 

 

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or an 

after- sales service agent,  or similarly trained and certificated personnel to avoid danger. 

 
 

7.  Cleaning,  maintenance and ordering of spare  parts 

 

Maintenance and cleaning work on the machine as well as removal of the safety devices may only be 

performed when the motor is switched off and the power cable has been un-plugged for the power 

source. 

 

7.1 Cleaning 

 

Keep all safety devices, air vents and the motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean cloth or blow it with compressed air at low 

pressure. 

 

We recommend that you clean the device immediately each time you have finished using it. 

 

Clean the equipment regularly with a moist cloth (not wet) and some soft soap. Do not use 

cleaning agents or solvents; these could attack the plastic parts of the equipment. 

Ensure 

that no water can seep into the device. 

 

7.2 Replace  the tiller blades 

For safety reasons, we recommend having the tiller blades replaced by an authorized professional 

only. 

Содержание STET1300













Отзывы: